Supplemental Restraint Systems. Front Seat Side Airbag Assembly Disposal

PRECAUTION
DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)
DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

Front Seat Side Airbag Assembly -- Disposal

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

1. PRECAUTION

HINT:

When scrapping a vehicle equipped with an SRS or disposing of the front seat side airbag, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the service department of the distributor.

CAUTION:

Never dispose of a front seat side airbag that has an unactivated airbag.
The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.
When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.
When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the front seat side airbag.
The front seat side airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
Use gloves and safety glasses when handling a front seat side airbag with a deployed airbag.
Do not apply water, etc. to a front seat side airbag with a deployed airbag.
Always wash your hands with water after completing the operation.
An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

2. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)

HINT:

Prepare a battery as the power source to deploy the airbag.

Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Supplemental Restraint Systems.Airbag System.Front Seat Side Airbag Assembly Disposal

Check the function of SST (LandCruiser RM000000U9M09BX_02_0001.html).

Read the precaution (LandCruiser RM000000KT10NVX.html).

Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

for Manual Seat:
1. Remove the front seat (LandCruiser RM00000465Y00YX.html).
  HINT:
  Keep the front seat in the cabin.

for Power Seat:
1. Remove the front seat (LandCruiser RM00000467200XX.html).
  HINT:
  Keep the front seat in the cabin.

for Walk in Seat Type:
1. Remove the front seat (LandCruiser RM0000046B800AX.html).
  HINT:
  Keep the front seat in the cabin.

Install SST.
1. Disconnect the connector (yellow-colored) from the front seat side airbag.
  NOTICE:
  When handling the airbag connector, take care not to damage the airbag wire harness.
2. Connect SST connector to the front seat side airbag connector.
  SST
  09082-00700
  09082-00820
  NOTICE:
  To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock.
3. for Manual Seat:
  Install the front seat (LandCruiser RM00000465W00ZX.html).
4. for Power Seat:
  Install the front seat (LandCruiser RM00000466Z00XX.html).
5. for Walk in Seat Type:
  Install the front seat (LandCruiser RM0000046B600AX.html).
6. Move SST at least 10 m (32.8 ft.) away from the vehicle front side window.
  Text in Illustration
  *1
  Battery
  *a
  10 m or more
7. Maintaining enough clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.
  NOTICE:
  Take care not to damage SST wire harness.
8. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

Text in Illustration
*1	Battery
*a	10 m or more

Deploy the airbag.
1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
2. Press SST activation switch to deploy the airbag.
  CAUTION:
  1. When deploying the airbag, make sure that no one is near the vehicle.
  2. The front seat side airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
  3. Use gloves and safety glasses when handling a front seat side airbag with a deployed airbag.
  4. Do not apply water to a front seat side airbag with a deployed airbag.
  5. Always wash your hands with water after completing the operation.
  HINT:
  The airbag is deployed as the LED of SST activation switch comes on.

3. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

NOTICE:

Be sure to follow the procedure detailed below when deploying the airbag.

HINT:

Prepare a battery as the power source to deploy the airbag.

Check the function of SST (LandCruiser RM000000U9M09BX_02_0002.html).

Remove the front seat side airbag assembly (LandCruiser RM00000465Z017X.html).

Using a service-purpose wire harness for the vehicle, tie the front seat side airbag to a tire.
Text in Illustration
*a
Wire Harness Diameter
*b
Stripped Wire Harness Section
Cross-sectional area of stripped wire harness section:
1.25 mm² (0.00192 in.²) or more
CAUTION:
If the wire harness is too thin or an alternative object is used to tie the front seat side airbag, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm² (0.00192 in.²).
HINT:
To calculate the cross-sectional area of the stripped wire harness section: Cross-sectional area = 3.14 x (Diameter)² / 4
1. Install the 2 nuts to the front seat side airbag.
2. Wind the wire harness around the stud bolts of the front seat side airbag as shown in the illustration.
3. Position the front seat side airbag inside a tire with the airbag deployment side facing inside.
  Text in Illustration
  *a
  Width
  *b
  Inner Diameter
  Tire size:
  Must exceed the following dimensions
  Width:
  185 mm (7.28 in.)
  Inner diameter:
  360 mm (14.2 in.)
4. Tie the front seat side airbag to the tire with several wire harnesses.
  CAUTION:
  1. Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the front seat side airbag may become loose due to the shock when the airbag is deployed.
  2. Always tie the front seat side airbag with the airbag deployment side facing inside.
  NOTICE:
  As the tire may be damaged by the airbag deployment, use a tire that you are planning to throw away.

Text in Illustration
*a	Wire Harness Diameter
*b	Stripped Wire Harness Section

Text in Illustration
*a	Width
*b	Inner Diameter

Connect SST connector to the front seat side airbag connector.
SST
09082-00820

Place tires.
Text in Illustration
*1
Tire
(2 or more)
1. Place at least 2 tires under the tire which the front seat side airbag is tied to.
2. Place at least 2 tires over the tire which the front seat side airbag is tied to. The top tire should have a disc wheel installed.
  NOTICE:
  1. Do not place SST connector under the tires because it could be damaged.
  2. As the disc wheel may be damaged by the airbag deployment, use a disc wheel that you are planning to throw away.
  3. As the tires may be damaged by the airbag deployment, use tires that you are planning to throw away.
3. Tie the tires together with 2 wire harnesses.
  CAUTION:
  Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.

Text in Illustration
*1	Tire (2 or more)

Connect SST connector.
SST
09082-00700
Text in Illustration
*1
Front Seat Side Airbag
*2
Battery
*a
10 m or more
NOTICE:
To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tires.

Text in Illustration
*1	Front Seat Side Airbag
*2	Battery
*a	10 m or more

Deploy the airbag.
1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
2. Check that no one is within a 10 m (32.8 ft.) radius of the tire which the front seat side airbag is tied to.
3. Press SST activation switch to deploy the airbag.
  CAUTION:
  When deploying the airbag, make sure that no one is near the tires.
  HINT:
  The airbag is deployed as the LED of SST activation switch comes on.

Dispose of the front seat side airbag.
CAUTION:
1. The front seat side airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
2. Use gloves and safety glasses when handling a front seat side airbag with a deployed airbag.
3. Do not apply water to a front seat side airbag with a deployed airbag.
4. Always wash your hands with water after completing the operation.
1. Remove the front seat side airbag from the tire.
2. Place the front seat side airbag in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.