Parking Assist Monitor System (W/ Side Monitor System) Calibration

This parking assist monitor system can be set from the diagnostic screen of the navigation receiver assembly*1 or radio and display receiver assembly*2 (display panel).

1. *1: for Navigation Receiver Type
   
2. *2: for Radio and Display Type
   

If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

1. *1: for Navigation Receiver Type
   
2. *2: for Radio and Display Type
   

NOTICE:

After the engine switch is turned off, the navigation receiver assembly*1 or radio and display receiver assembly*2 requires approximately a minute to record various types of memory and settings. As a result, after turning the engine switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

HINT:

The adjustment values stored while performing parking assist monitor system calibration are stored in the parking assist ECU.

Preparation for adjustment

1. Park the vehicle with the steering wheel centered.
   





2. Set a target bar for optical axis adjustment of the rear television camera assembly.
   

   HINT:

   Only when adjusting the optical axis of the camera, create a target bar for adjustment.

   Dimension:

   Area	Specification
   A	990 to 1000 mm (3.25 to 3.28 ft.)
   B	1995 to 2005 mm (6.55 to 6.58 ft.)

   Text in Illustration

   *a	Vehicle Center
   *b	Target Bar for Back Camera Adjustment
   *c	Vehicle End
   *d	Front Side

   HINT:

   1. Set a piece of tape on the ground as the target bar for adjustment. Its width and length are 20 to 30 mm (0.787 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the navigation receiver assembly*1 or radio and display receiver assembly*2 and choose a tape color which can be easily seen.
      
   2. Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
      
   3. Check that the back door is fully closed.
      

3. Set a target bar for optical axis adjustment of the side television camera.
   

   HINT:

   Only when adjusting the optical axis of the camera, create a target bar for adjustment.

   
   
   1. for LHD:
      
      
      
      
      
      
   
   
   2. for RHD:
      
      
      
      
      
      
   
   

   Text in Illustration

   *a	Target Bar for Side Camera Adjustment	*b	Front Wheel Axis
   *c	Front Side	*d	Vehicle Center

   
   

   Dimension:

   
   

   A	B	C	D	E	F
   1183 mm (3.88 ft.)	1181 mm (3.87 ft.)	500 mm (1.64 ft.)	500 mm (1.64 ft.)	500 mm (1.64 ft.)	180 mm (7.09 in.)

   HINT:

   Target bars for side camera adjustment should be made with 2 pieces of 2.5 cm wide tape; one piece should be 100 cm (3.28 ft.) (C+D) and the other should be 68 cm (2.23 ft.) (E+F) long. Check the tape color on the multi-display (display panel) and choose a tape color which can be easily seen.

Start diagnostic mode.

1. for Navigation Receiver Type: LandCruiser RM0000011BU0W7X.html
   
2. for Radio and Display Type: LandCruiser RM0000011BU0W8X.html
   

NOTICE:

Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

HINT:

The displayed items may differ depending on vehicle specifications.

1. Select "Function Check/Setting" on the "Service Menu" screen.
   





2. Select "Camera Setting" on the "Function Check/Setting I" screen.
   





3. Select "Next" on the "Signal Check" screen.
   

   NOTICE:

   1. When "CHK" (red) is displayed for any items on the "Signal Check" screen, selecting "Next" will not change the screen to the "Side Camera Position Setting" screen.
      
   2. When "CHK" (red) is displayed for any items on the "Signal Check" screen, perform inspections using the "Signal Check" screen (LandCruiser RM000003WVZ06KX.html).
      

   HINT:

   1. When the outer mirrors are retracted, selecting "Next" will not change the screen to the "Side Camera Position Setting" screen.
      
   2. If the screen does not change to the "Side Camera Position Setting" screen even though the outer mirrors are extended, perform the "MIRROR SW" check on the "Signal Check" screen (LandCruiser RM000003WVZ06KX.html).
      
   3. If the screen does not change to the "Side Camera Position Setting" screen even after "OK" (blue) is displayed as a result of the MIRROR SW check on the "Signal Check" screen, replace the parking assist ECU (LandCruiser RM000003WVZ06KX.html).
      

Side Camera Position Setting:

HINT:

Colors used on the "Side Camera Position Setting" screen

1. Perform the roll angle adjustment.
   

   1. Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
      

2. Perform the vertical and horizontal position adjustment.
   

   1. Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      

3. Select "Next" to display "Side Verify Mode".
   

Side Verify Mode:

1. Check that the red cross and the target adjustment bar are aligned.
   

   HINT:

   If they are not aligned, select "Back" and perform "Side Camera Position Setting" again.

2. Select "Next" to display "Side Camera Signal Check".
   

Side Camera Signal Check:

1. Select "Next" to store the side camera aiming adjustment value and change the screen to the "Steering Angle Setting" screen.
   

   HINT:

   1. When "Next" is selected, a beep will sound to confirm that the side camera aiming adjustment values have been stored.
      
   2. The adjustment value will not be stored unless "Next" is selected.
      

Steering Angle Setting:

1. Perform the "STEERING CENTER MEMORIZE" operation.
   

   1. Check that the steering wheel is centered, and then select "STEERING CENTER MEMORIZE".
      

   HINT:

   When performing removal and installation, or replacement of the television camera, steering angle adjustment is not required.

2. Perform the "MAX STEERING ANGLE MEMORIZE" operation.
   

   1. After adjusting the steering angle neutral point, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the "Back Camera Position Setting" screen.
      

      HINT:

      1. The "Next" button does not respond until the system stores the steering angle neutral point and maximum steering angle.
         
      2. It is also possible to start by initially turning the steering to the right side.
         
      3. When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the steering adjustment values have been stored.
         
      4. The adjustment value will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected after turning the steering wheel side to side.
         
      5. When "Back" is selected, the screen changes to "Side Verify Mode" without storing the set values.
         
      6. Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the adjustment value to be stored if the steering sensor is malfunctioning.
         
      7. If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering sensor.
         

Back Camera Position Setting:

HINT:

1. When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed.
   
2. When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
   
3. If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after back door is closed) (LandCruiser RM000003XLE06BX.html).
   

1. Perform the roll angle adjustment.
   

   1. Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
      

2. Perform the vertical and horizontal position adjustment.
   

   1. Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      

3. Select the "Next" to display "Back Verify Mode".
   

Back Verify Mode:

1. Check that A and the target adjustment bar are overlapping.
   

   1. If the steering angle neutral point is not aligned, perform the "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" operations.
      
   2. If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the camera position setting operation.
      

2. Selecting "OK" will return the screen to the "Service Menu" screen, and complete the adjustment.
   

   HINT:

   1. The update is not completed until "OK" is selected.
      
   2. When "OK" is selected, a beep will sound to confirm that the rear camera aiming adjustment values have been stored.
      
   3. The adjustment values are not stored until the beep has sounded.
      

Finish diagnostic mode.

1. for Navigation Receiver Type: LandCruiser RM0000011BU0W7X.html
   
2. for Radio and Display Type: LandCruiser RM0000011BU0W8X.html
   

Preparation for adjustment

1. Park the vehicle with the steering wheel centered.
   

Start diagnostic mode.

1. for Navigation Receiver Type: LandCruiser RM0000011BU0W7X.html
   
2. for Radio and Display Type: LandCruiser RM0000011BU0W8X.html
   

NOTICE:

Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

HINT:

The displayed items may differ depending on vehicle specifications.

1. Select "Function Check/Setting" on the "Service Menu" screen.
   





2. Select "Camera Setting" on the "Function Check/Setting" screen.
   





3. Select "Steering Angle Setting" on the "Mode Setting" screen.
   

   HINT:

   To select a grayed out item, select and hold the item for 2 seconds or more.





4. Select "Next" on the "Signal Check" screen.
   

   NOTICE:

   1. When "CHK" (red) is displayed for any items on the "Signal Check" screen, selecting "Next" will not change the screen to the "Steering Angle Setting" screen.
      
   2. When "CHK" (red) is displayed for any items on the "Signal Check" screen, perform inspections using the "Signal Check" screen (LandCruiser RM000003WVZ06KX.html).
      

Steering Angle Setting:

1. Perform the "STEERING CENTER MEMORIZE" operation.
   

   1. Check that the steering wheel is centered, and then select "STEERING CENTER MEMORIZE".
      

   HINT:

   When performing removal and installation, or replacement of the television camera, steering angle adjustment is not required.

2. Perform the "MAX STEERING ANGLE MEMORIZE" operation.
   

   1. After adjusting the steering angle neutral point, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the "Mode Setting" screen.
      

   HINT:

   1. The "Next" button does not respond until the system stores the steering angle neutral point and maximum steering angle.
      
   2. It is also possible to start by initially turning the steering to the right side.
      
   3. When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the steering adjustment values have been stored.
      
   4. The adjustment value will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected after turning the steering wheel side to side.
      
   5. When "Back" is selected, the screen changes to "Signal Check" without storing the set values.
      
   6. Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the adjustment value to be stored if the steering sensor is malfunctioning.
      
   7. If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering sensor.
      

3. Select "OK" to display "Mode Setting".
   

Finish diagnostic mode.

1. for Navigation Receiver Type: LandCruiser RM0000011BU0W7X.html
   
2. for Radio and Display Type: LandCruiser RM0000011BU0W8X.html
   

Confirm steering angle adjustment.

HINT:

If the steering angle has been adjusted, confirm the steering angle adjustment on the parking assist monitor screen after finishing diagnostic mode.

1. Check on the parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.
   

   HINT:

   If the predicted path line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" again.

Preparation for adjustment

1. Park the vehicle with the steering wheel centered.
   





2. Set a target bar for optical axis adjustment of the rear television camera.
   

   HINT:

   Only when adjusting the optical axis of the camera, create a target bar for adjustment.

   Dimension:

   Area	Specification
   A	990 to 1000 mm (3.25 to 3.28 ft.)
   B	1995 to 2005 mm (6.55 to 6.58 ft.)

   Text in Illustration

   *a	Vehicle Center
   *b	Target Bar for Back Camera Adjustment
   *c	Vehicle End
   *d	Front Side

   HINT:

   1. Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.787 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the multi-display and choose a tape color which can be easily seen.
      
   2. Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
      
   3. Check that the back door is fully closed.
      

Start diagnostic mode.

1. for Navigation Receiver Type: LandCruiser RM0000011BU0W7X.html
   
2. for Radio and Display Type: LandCruiser RM0000011BU0W8X.html
   

NOTICE:

Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

HINT:

The displayed items may differ depending on vehicle specifications.

1. Select "Function Check/Setting" on the "Service Menu" screen.
   





2. Select "Camera Setting" on the "Function Check/Setting" screen.
   





3. Select "Back Camera Setting" on the "Mode Setting" screen.
   

   HINT:

   To select a grayed out item, select and hold the item for 2 seconds or more.





4. Select "Next" on the "Signal Check" screen.
   

   NOTICE:

   1. When "CHK" (red) is displayed for any items on the "Signal Check" screen, selecting "Next" will not change the screen to the "Back Camera Position Setting" screen.
      
   2. When "CHK" (red) is displayed for any items on the "Signal Check" screen, perform inspections using the "Signal Check" screen (LandCruiser RM000003WVZ06KX.html).
      

Back Camera Position Setting:

HINT:

1. When adjusting the camera optical axis, "Back door is open. Do not use the rear view monitor when the back door is not completely closed." is displayed even after the back door has been closed.
   
2. When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
   
3. If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after back door is closed) (LandCruiser RM0000035D7079X.html).
   

1. Perform the roll angle adjustment.
   

   1. Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
      

2. Perform the vertical and horizontal position adjustment.
   

   1. Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
      

3. Select the "Next" button on the "Back Camera Position Setting" screen.
   

Back Verify Mode:

1. Check that A and the target adjustment bar are overlapping.
   

   1. If the steering angle neutral point is not aligned, perform the "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" operations.
      
   2. If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the camera position setting operation.
      

2. Selecting "OK" will return the screen to the "Service Menu", and complete the adjustment.
   

   HINT:

   1. The update is not completed until "OK" is selected.
      
   2. When "OK" is selected, a beep will sound to confirm that the rear camera aiming adjustment values have been stored.
      

Finish diagnostic mode.

1. for Navigation Receiver Type: LandCruiser RM0000011BU0W7X.html
   
2. for Radio and Display Type: LandCruiser RM0000011BU0W8X.html