Steering Column Assembly (For Power Tilt And Power Telescopic Steering Column) Removal


  1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE FRONT WHEEL LH

  4. REMOVE STEERING WHEEL ASSEMBLY

  5. REMOVE STEERING COLUMN LOWER COVER

  6. REMOVE STEERING COLUMN UPPER COVER

  7. REMOVE TILT AND TELESCOPIC SWITCH

  8. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  9. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

  10. REMOVE NO. 1 INSTRUMENT LOWER PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

  11. REMOVE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

  12. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

  13. DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

  14. REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

  15. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

Steering Column Assembly (For Power Tilt And Power Telescopic Steering Column) -- Removal


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering wheel (LandCruiser RM000000KT10NVX.html).
HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  1. Disable the auto tilt away function by changing the customize parameter (LandCruiser RM000004KI4013X.html).

    NOTICE:
    Record the current customize parameter setting (whether the auto tilt away function is enabled or disabled) in order to restore the current setting after finishing the operation.
    HINT:
    Performing the above operation causes the auto tilt away function to be disabled when the engine switch is turned off.

  1. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

  1. Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


3. REMOVE FRONT WHEEL LH


4. REMOVE STEERING WHEEL ASSEMBLY
(LandCruiser RM0000039SA01YX.html)


5. REMOVE STEERING COLUMN LOWER COVER


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the steering column lower cover.

    NOTICE:
    Do not damage the tilt and telescopic switch.


6. REMOVE STEERING COLUMN UPPER COVER


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Detach the 4 clips.

  1. Detach the claw and remove the steering column upper cover.



7. REMOVE TILT AND TELESCOPIC SWITCH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Steering Column.Power Tilt And Power Telescopic Steering Column System.Steering Column Assembly (For Power Tilt And Power Telescopic Steering Column) Removal

  1. Disconnect the connector.

  1. Detach the claw and pull out the tilt and telescopic switch.

    NOTICE:
    Pushing on the claw too hard will break the claw.


8. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  1. Disconnect the connectors from the combination switch with spiral cable.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Use pliers to hold the clamp and raise the claw with a screwdriver. Then remove the combination switch switch assembly with spiral cable sub-assembly from the steering column assembly.



9. REMOVE INSTRUMENT LOWER PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)
(LandCruiser RM0000046J800OX.html)


10. REMOVE NO. 1 INSTRUMENT LOWER PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
(LandCruiser RM000003YPV037X.html)


11. REMOVE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

  1. Detach the claws and remove the wire harness protector and wire harness.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Steering Column.Power Tilt And Power Telescopic Steering Column System.Steering Column Assembly (For Power Tilt And Power Telescopic Steering Column) Removal

  1. Put matchmarks on the steering actuator and steering column.

    Text in Illustration
    *a
    		Matchmark

  1. Remove the bolt.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 4 nuts, steering column and steering shaft stopper.



12. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. w/ KDSS:
    Remove the 7 clips and fender apron seal.



    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. w/o KDSS:
    Remove the 5 clips and fender apron seal.



13. DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Steering Column.Power Tilt And Power Telescopic Steering Column System.Steering Column Assembly (For Power Tilt And Power Telescopic Steering Column) Removal

  1. Put matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.

    Text in Illustration
    *a
    		Matchmark

  1. Remove the bolt, and then pull out the intermediate shaft toward the inside of the vehicle.



14. REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 4 bolts and steering column hole cover from the vehicle.



15. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Steering Column.Power Tilt And Power Telescopic Steering Column System.Steering Column Assembly (For Power Tilt And Power Telescopic Steering Column) Removal

  1. Put matchmarks on the No. 2 steering intermediate shaft and power steering gear.

    Text in Illustration
    *a
    		Matchmark

  1. Remove the bolt and No. 2 steering intermediate shaft from the power steering gear.