Kinetic Dynamic Suspension System Dtc Check / Clear

  1. CHECK DTC (USING INTELLIGENT TESTER)

  1. CHECK DTC (USING SST CHECK WIRE)

Kinetic Dynamic Suspension System -- Dtc Check / Clear



CHECK DTC (USING INTELLIGENT TESTER)

  1. Check DTC.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and the intelligent tester on.

    3. Enter the following menus: Chassis / KDSS / DTC.

    4. Read DTCs by following the prompts on the intelligent tester screen.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  2. Clear DTC.

    HINT:
    After repairing malfunctions, clear the DTCs.

    1. Connect the intelligent tester to the DLC3

    2. Turn the ignition switch to ON and the intelligent tester on.

    3. Enter the following menus: Chassis / KDSS / DTC.

    4. Clear the DTCs by following the prompts on the intelligent tester screen.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

CHECK DTC (USING SST CHECK WIRE)


  1. Check DTC.



      Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Suspension Control.Air Suspension System.Kinetic Dynamic Suspension System Dtc Check / Clear

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040
      NOTICE:
      Do not connect the wrong terminals as this will cause damage.
      Text in Illustration
      *a
      		Front view of DLC3

    2. Turn the ignition switch to ON.

    3. Read the DTCs output from the KDSS indicator light in the combination meter.

      HINT:
      1. When only 1 DTC is stored, the KDSS indicator light outputs the same code after an interval of 4 seconds. Example: When DTC 31 is stored, the light blinks 3 times, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.
      2. When 2 or more DTCs are stored, the KDSS indicator light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.

    4. Refer to the Diagnostic Trouble Code Chart (LandCruiser RM000001N8Y01VX.html) for DTC information.

    5. After completing the check, remove SST check wire from the DLC3.

      SST
      09843-18040


  2. Clear DTC.

    1. Make sure that the ignition switch is off.



      2. Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Suspension Control.Air Suspension System.Kinetic Dynamic Suspension System Dtc Check / Clear

    2. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040
      NOTICE:
      Do not connect the wrong terminals as this will cause damage.
      Text in Illustration
      *a
      		Front view of DLC3

    3. Turn the ignition switch to ON.

    4. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    5. Check that the KDSS indicator light blinks at intervals of 0.25 seconds on and 0.25 seconds off.

    6. Turn the ignition switch off.

    7. Remove SST from the terminals of the DLC3.

      SST
      09843-18040
      NOTICE:
      After clearing the DTCs, check if the malfunction is detected again. As it is necessary to perform certain system operations or drive the vehicle in order to detect some malfunctions, check that malfunctions are no longer present after performing all necessary operations.