1Gd-Ftv Engine Control. Dtc P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)

P2032
DTC Detection Drive Pattern	DTC Detection Condition	Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds and allowing 11 minutes to elapse after starting the engine.	No. 2 exhaust gas temperature sensor output voltage is below 0.2 V for 3 seconds or more when all conditions are met. (1 trip detection logic): After starting the engine, 11 minutes or more elapses Coolant temperature is 70°C (158°F) or more The exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds.	Open or short in No. 2 exhaust gas temperature sensor circuit No. 2 exhaust gas temperature sensor ECM

P2033
DTC Detection Drive Pattern	DTC Detection Condition	Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds and allowing 11 minutes to elapse after starting the engine.	No. 2 exhaust gas temperature sensor output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met. (1 trip detection logic): After starting the engine, 11 minutes or more elapses Engine is running Coolant temperature is 60°C (140°F) or more	Open or short in No. 2 exhaust gas temperature sensor circuit No. 2 exhaust gas temperature sensor ECM

Related Data List
DTC No.	Data List
P2032 P2033	Exhaust Temperature B1S2

HINT:

DTC P20CF (Exhaust fuel addition injector malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.
Sensor 2 represents the sensor located upstream of the DPF catalytic converter.
When DTC P2032 or P2033 is output, check the exhaust gas temperature indicated by "Powertrain / Engine and ECT / Exhaust Temperature B1S2 using the GTS.

Reference:
Condition	Exhaust Temperature B1S2	No. 2 Exhaust Gas Temperature Sensor Condition
Idling after warm-up	Constant at between 50 and 700°C (122 and 1292°F)	Normal
	-40°C (-40°F)	Open circuit
	1000°C (1832°F) or higher	Short circuit

MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the No. 2 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

Refer to DTC P0545 (LandCruiser RM00000188D0AIX_03.html).

INSPECTION PROCEDURE

NOTICE:

After replacing the ECM, the new ECM needs registration (LandCruiser RM0000012XK0AUX.html) and initialization (LandCruiser RM000000TIN08HX.html).

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.READ VALUE USING GTS (EXHAUST TEMPERATURE B1S2)

Connect the GTS to the DLC3.

Turn the engine switch on (IG) and turn the GTS on.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

Read the value.

Standard:: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.

Result
Temperature Displayed	Proceed to
-40°C (-40°F) (After warming up the engine)	A
1000°C (1832°F) or higher	B
OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining an engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm	C

HINT:

If there is a short circuit, the GTS will indicate -40°C (-40°F).
If there is an open circuit, the GTS will indicate 1000°C (1832°F) or higher.

Go to step 6

Go to step 11

A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.1Gd-Ftv Engine Control.Ecd System.
Dtc
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)

Disconnect the No. 2 exhaust gas temperature sensor connector.

Connect terminals 1 (E2) and 2 (THCI) of the exhaust gas temperature sensor wire harness side connector.

Connect the GTS to the DLC3.

Turn the engine switch on (IG) and turn the GTS on.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

Read the value.
Standard:
1000°C (1832°F) or higher
Text in Illustration
*1
No. 2 Exhaust Gas Temperature Sensor
*2
ECM
*a
Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor)

Text in Illustration
*1	No. 2 Exhaust Gas Temperature Sensor
*2	ECM
*a	Front view of wire harness connector (to No. 2 Exhaust Gas Temperature Sensor)

Reconnect the exhaust gas temperature sensor connector.

Go to step 4

OK

3.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

Replace the No. 2 exhaust gas temperature sensor (LandCruiser RM000005UK3000X.html).

Go to step 11

4.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)

Disconnect the No. 2 exhaust gas temperature sensor connector.

Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection
Condition
Specified Condition
C166-1 (E2) - C149-24 (ETCI)
Always
Below 1 Ω
C166-2 (THCI) - C149-25 (THCI)
Always
Below 1 Ω

Reconnect the No. 2 exhaust gas temperature sensor connector.

Reconnect the ECM connector.

Go to step 10

OK

5.REPLACE ECM

Replace the ECM (LandCruiser RM0000013Z002DX.html).

Go to step 11

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

Disconnect the No. 2 exhaust gas temperature sensor connector.

Connect the GTS to the DLC3.

Turn the engine switch on (IG) and turn the GTS on.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

Read the value.
Standard:
-40°C (-40°F)
Text in Illustration
*1
No. 2 Exhaust Gas Temperature Sensor
*2
ECM

Text in Illustration
*1	No. 2 Exhaust Gas Temperature Sensor
*2	ECM

Reconnect the No. 2 exhaust gas temperature sensor connector.

Go to step 8

OK

7.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

Replace the No. 2 exhaust gas temperature sensor (LandCruiser RM000005UK3000X.html).

Go to step 11

8.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)

Disconnect the No. 2 exhaust gas temperature sensor connector.

Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection
Condition
Specified Condition
C166-2 (THCI) or C149-25 (THCI) - Body ground and other terminals
Always
10 kΩ or higher

Reconnect the No. 2 exhaust gas temperature sensor connector.

Reconnect the ECM connector.

Go to step 10

OK

9.REPLACE ECM

Replace the ECM (LandCruiser RM0000013Z002DX.html).

Go to step 11

10.REPAIR OR REPLACE HARNESS OR CONNECTOR

Repair or replace the harness or connector.

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Connect the GTS to the DLC3.

Clear the DTCs (LandCruiser RM000000PDK1E5X.html).

Start the engine.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds and allowing 11 minutes to elapse after starting the engine.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Confirm that the DTC is not output again.

END

Tester Connection	Condition	Specified Condition
C166-1 (E2) - C149-24 (ETCI)	Always	Below 1 Ω
C166-2 (THCI) - C149-25 (THCI)	Always	Below 1 Ω