Cruise Control System Data List / Active Test

  1. READ DATA LIST

Cruise Control System -- Data List / Active Test



READ DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Powertrain / Cruise Control / Data List.

  5. According to the display on the intelligent tester, read the "Data List".

    Cruise Control
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    CCS Vehicle Spd
    		Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    		Actual vehicle speed displayed
    		-
    CCS Mem Vehicle Spd
    		Memory vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph)
    		Actual vehicle speed stored in memory
    		-
    Throttle Opening Angle*1
    		Throttle opening angle / min.: 0 deg, max.: 125 deg
    		Actual required throttle opening angle
    		-
    Throttle Opening Angle*2
    		Throttle opening angle / min.: 0%, max.: 100%
    		Actual required throttle opening angle
    		-
    Cruise Control
    		Cruise control system active condition / ON or OFF
    		ON: Cruise control system activated
    OFF: Cruise control system inactivated
    		-
    CCS Main SW M-CPU
    		Cruise control main switch signal (Main CPU) / ON or OFF
    		ON: Cruise control main switch (Main CPU) on
    OFF: Cruise control main switch (Main CPU) off
    		-
    CCS Ready M-CPU
    		Cruise control system standby condition (Main CPU) / ON or OFF
    		ON: Cruise control main switch (Main CPU) on
    OFF: Cruise control main switch (Main CPU) off
    		-
    CCS Indicator M-CPU
    		Cruise main indicator signal (Main CPU) / ON or OFF
    		ON: CRUISE main indicator (Main CPU) on
    OFF: CRUISE main indicator (Main CPU) off
    		-
    Cancel Switch
    		CANCEL switch signal / ON or OFF
    		ON: CANCEL switch on
    OFF: CANCEL switch off
    		-
    SET/COAST Switch
    		-SET switch signal / ON or OFF
    		ON: -SET switch on
    OFF: -SET switch off
    		-
    RES/ACC Switch
    		+RES switch signal / ON or OFF
    		ON: +RES switch on
    OFF: +RES switch off
    		-
    Stop Light SW M-CPU
    		Stop light switch signal (Main CPU) / ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    Cruise Operation Status*1
    		PNP switch signal (D position) ON or OFF
    		ON: Shift lever on D or 4
    OFF: Shift lever not on D or 4
    		-
    Cruise Operation Status*2
    		PNP switch signal (D position) ON or OFF
    		ON: Shift lever on D or 3
    OFF: Shift lever not on D or 3
    		-
    # Codes
    		Number of trouble codes / min.: 0, max.: 255
    		-
    		-

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV