Rear Seat Outer Belt Assembly -- Installation |
- HINT:
- Use the same procedures for the LH side and RH side.
- The procedures listed below are for the RH side.
- A bolt without a torque specification is shown in the standard bolt chart (Toyota Fortuner RM00000118W017X.html).
| 1. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY OUTER RH |
 |
Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the bolt as shown in the illustration.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Connect the shoulder anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
 |
Close the cover cap.
| 2. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH |
 |
Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the bolt as shown in the illustration.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Connect the shoulder anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
|
Close the cover cap.
| 3. INSTALL QUARTER INSIDE TRIM BOARD RH |
Detach the 8 claws and 10 clips to install the quarter inside trim board.
Install the clip.
Connect the rear No. 2 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Connect the rear No. 1 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the outer lap belt anchor cover.
- HINT:
- Use the same procedure for both outer lap belt anchor covers.
| 4. CONNECT REAR NO. 2 SEAT BELT ASSEMBLY OUTER RH |
 |
Connect the seat belt's floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Install the belt outer anchor cover.
 |
| 5. CONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH |
 |
Connect the seat belt's floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Install the belt outer anchor cover.
 |
| 6. INSTALL QUARTER TRIM HOOK |
- HINT:
- Use the same procedure for both quarter trim hooks.
Install the quarter trim hook with the screw.
| 7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
- HINT:
- Use the same procedure described for the LH side.
| 8. INSTALL REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure described for the LH side.
| 9. INSTALL BACK DOOR SCUFF PLATE |
Attach the 4 claws, 2 guides and 6 clips to install the back door scuff plate.
| 10. INSTALL REAR NO. 2 SEAT ASSEMBLY RH |
Fully tilt the seatback forward.
Place the seat onto the lock striker.
- NOTICE:
- Be careful not to damage the vehicle body.
 |
Tighten the bolt on the rear side of the seat.
- Torque:
- 37 N*m{377 kgf*cm, 27 ft.*lbf}
Tighten the bolt on the front side of the seat.
- Torque:
- 37 N*m{377 kgf*cm, 27 ft.*lbf}
Fully lock the seat to the lock striker.
- HINT:
- Confirm that the seat is firmly locked to the lock striker.
| 11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |