Dtc C1267/67 Brake Pedal Load Sensing Switch


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH AND BRAKE PEDAL LOAD SENSING SWITCH)

RECONFIRM DTC

INSPECT BRAKE PEDAL LOAD SENSING SWITCH

CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

DTC C1267/67 Brake Pedal Load Sensing Switch


DESCRIPTION

The brake pedal load sensing switch is turned on when the brake pedal is depressed with force exceeding a predetermined level.
The skid control ECU detects if the brake pedal is depressed or not via this circuit.

DTC Code
DTC Detection Condition
Trouble Area
C1267/67
When one of the following conditions is met:
  1. An open or short in the brake pedal load sensing switch continues for 0.3 seconds or more.
  2. Immediately after the ignition switch is turned ON, the brake pedal load sensing switch is ON and the stop light switch is OFF for 10 seconds or more.
  3. While the vehicle speed changes from 0 km/h (0 mph) to 30 km/h (18 mph), the condition that the brake pedal load sensing switch remains ON occurs 5 times in succession.
  4. With the stop light switch ON, the brake pedal load sensing switch OFF, and the master cylinder pressure 6 MPa (61.2 kgf/cm2, 870 psi) or more, the deceleration is 0.4 G or more for 1 second or more.
  5. With the stop light switch ON, the brake pedal load sensing switch OFF, and the master cylinder pressure 6 MPa (61.2 kgf/cm2, 870 psi) or more, the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.
  1. Brake pedal load sensing switch (Brake with switch pedal sub-assembly)
  2. Brake pedal load sensing switch circuit
  3. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C1267/67 Brake Pedal Load Sensing Switch


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Toyota Fortuner RM000000XHR02TX.html).
HINT:
When C1249/49 is output together with C1267/67, inspect and repair the trouble areas indicated by C1249/49 first (Toyota Fortuner RM000000XIE0CCX.html).
1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH AND BRAKE PEDAL LOAD SENSING SWITCH)

  1. Connect the intelligent tester to the DLC3.

  1. Select the Data List mode on the intelligent tester (Toyota Fortuner RM000000XHW080X.html).

    ABS/VSC/TRC
    Tester Display
    		Measurement Item / Range
    		Normal Condition
    		Diagnostic Note
    Stop Light SW
    		Stop light switch /
    ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    Brake Pedal Load Sensing SW
    		Brake pedal load sensing switch /
    ON or OFF
    		ON: Brake pedal depressed beyond a specified point
    OFF: Brake pedal not depressed beyond a specified point
    		-

  1. Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.

  1. Slowly depress the brake pedal, and check the illumination of the stop light switch and brake pedal load sensing switch.

    OK:
    First the stop light switch turns ON, and then the brake pedal load sensing switch turns ON.

    Result
    Result
    		Proceed to
    OK
    		A
    NG (The brake pedal load sensing switch does not turn on)
    		B
    NG (The brake pedal load sensing switch turns on first)
    		C


B
Go to step 3

C
Go to step 5
A


2.RECONFIRM DTC

  1. Clear the DTC(s) (Toyota Fortuner RM000000XHV09NX.html).

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Toyota Fortuner RM000000XHV09NX.html).

    Result
    Result
    		Proceed to
    DTC C1267/67 is not output
    		A
    DTC C1267/67 is output
    		B


B
REPLACE BRAKE ACTUATOR ASSEMBLY
A

CHECK FOR INTERMITTENT PROBLEMS

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH

Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C1267/67 Brake Pedal Load Sensing Switch

NOTICE:
  1. Do not remove the brake pedal load sensing switch from the brake with switch pedal sub-assembly.
  2. When there is a malfunction in the brake pedal load sensing switch, replace the brake with switch pedal sub-assembly.

  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake pedal load sensing switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    2 - 1
    		Brake pedal load sensing switch OFF
    (Brake pedal depressed)
    		950 to 1050 Ω
    2 - 1
    		Brake pedal load sensing switch ON
    (Brake pedal released)
    		203 to 223 Ω


NG
REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C1267/67 Brake Pedal Load Sensing Switch

  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Disconnect the brake pedal load sensing switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    S25-27 (FSW+) - B13-2
    		Always
    		Below 1 Ω
    S25-27 (FSW+) - Body ground
    		Always
    		 10 kΩ or higher
    B13-1 - Body ground
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch installation (Toyota Fortuner RM0000010K500AX.html).

    OK:
    The brake pedal height and stop light switch installation are normal.


NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH
OK

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY