Vehicle Stability Control System Data List / Active Test

  1. DATA LIST

  1. ACTIVE TEST

Vehicle Stability Control System -- Data List / Active Test



DATA LIST
HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  7. According to the display on the tester, read the "Data List".

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    ABS Warning Light
    		ABS warning light / ON or OFF
    		ON: Warning light ON
    OFF: Warning light OFF
    		-
    VSC Warning Light
    		VSC OFF indicator light / ON or OFF
    		ON: Indicator light ON
    OFF: Indicator light OFF
    		-
    Brake Warning Light
    		Brake warning light / ON or OFF
    		ON: Warning light ON
    OFF: Warning light OFF
    		-
    Slip Indicator Light
    		Slip indicator light / ON or OFF
    		ON: Indicator light ON
    OFF: Indicator light OFF
    		-
    Buzzer
    		Skid control buzzer / ON or OFF
    		ON: Buzzer ON
    OFF: Buzzer OFF
    		-
    Stop Light SW
    		Stop light switch / ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    		-
    Parking Brake SW
    		Parking brake switch / ON or OFF
    		ON: Parking brake applied
    OFF: Parking brake released
    		-
    Main Idle SW
    		Main idle switch / ON or OFF
    		ON: Accelerator pedal released
    OFF: Accelerator pedal depressed
    		-
    Brake Pedal Load Sensing SW
    		Brake pedal load sensing switch / ON or OFF
    		ON: Brake pedal depressed beyond the specified point
    OFF: Brake pedal not depressed beyond the specified point
    		-
    Gear Position
    		Gear position information / P,N, R, 1st-8th, FAIL, NOT R
    		Actual gear position
    		-
    Shift Lever Position
    		Shift lever position information / P,N, R, D/M, 1st-6th/B, FAIL
    		Actual shift lever position
    		-
    Shift Information
    		Shift information / ON or OFF
    		ON: During gear change
    		-
    Inspection Mode
    		Inspection mode / OTHER or INSPECT
    		OTHER: Normal mode
    INSPECT: Inspection mode
    		-
    Number of IG ON (Inspection)
    		Number of ignition switch being turned to ON after entering inspection mode / min.: 0, max.: 255
    		-
    		-
    Master Cylinder Sensor
    		Master cylinder pressure sensor / min.: 0 V, max.: 5 V
    		When brake pedal is released: 0.3 to 0.9 V
    		Reading increases when brake pedal is depressed
    Zero Point of M/C
    		Memorized zero value / min.: -12.5 MPa, max.: 12.4 MPa
    		-
    		-
    Deceleration Sensor
    		Acceleration sensor / min.: -18.52 m/s2, max.: 18.39 m/s2
    		-
    		Reading changes when vehicle is bounced
    Zero Point of Decele
    		Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
    		-
    		-
    Deceleration Sensor 2
    		Acceleration sensor 2 / min.: -18.52 m/s2, max.: 18.39 m/s2
    		-
    		Reading changes when vehicle is bounced
    Zero Point of Decele 2
    		Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
    		-
    		-
    Yaw Rate Sensor
    		Yaw rate sensor / min.: -128 deg/s, max.: 127 deg/s
    		Vehicle stationary: 0 deg/s
    Right turn: -128 to 0 deg/s
    Left turn: 0 to 127 deg/s
    		-
    Zero Point of Yaw Rate
    		Memorized zero value / min.: -128 deg/s, max.: 127 deg/s
    		-
    		-
    Yaw Rate Sensor 2
    		Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s
    		Vehicle stationary: 0 deg/s
    Right turn: -128 to 0 deg/s
    Left turn: 0 to 127 deg/s
    		-
    Zero Point of Yaw Rate 2
    		Memorized zero value / min.: -128 deg/s, max.: 127 deg/s
    		-
    		-
    Steering Angle Sensor
    		Steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg
    		Left turn: Increases
    Right turn: Decreases
    		-
    Zero Point of Steering Angle
    		Memorized zero value / min.: -3276.8 deg, max.: 3276.7 deg
    		-
    		-
    Lateral G
    		Lateral G / min.: -25.11 m/s2, max.: 24.91 m/s2
    		-
    		-
    Forward and Rearward G
    		Forward and backward G / min.: -25.11 m/s2, max.: 24.91 m/s2
    		-
    		-
    Yaw Rate Value
    		Yaw rate value / min.: -128 deg/s, max.: 127 deg/s
    		-
    		-
    Steering Angle Value
    		Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg
    		-
    		-
    FR Wheel Speed
    		Front wheel RH speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
    		Actual wheel speed
    		Similar speed as indicated on speedometer
    FL Wheel Speed
    		Front wheel LH speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
    		Actual wheel speed
    		Similar speed as indicated on speedometer
    RR Wheel Speed
    		Rear wheel RH speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
    		Actual wheel speed
    		Similar speed as indicated on speedometer
    RL Wheel Speed
    		Rear wheel LH speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202.8 mph)
    		Actual wheel speed
    		Similar speed as indicated on speedometer
    Vehicle Speed
    		Maximum wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
    		Actual vehicle speed
    		Speed indicated on speedometer
    FR Wheel Acceleration
    		Front wheel RH acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    		-
    		During deceleration/acceleration: Changes continuously
    FL Wheel Acceleration
    		Front wheel LH acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    		-
    		During deceleration/acceleration: Changes continuously
    RR Wheel Acceleration
    		Rear wheel RH acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    		-
    		During deceleration/acceleration: Changes continuously
    RL Wheel Acceleration
    		Rear wheel LH acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
    		-
    		During deceleration/acceleration: Changes continuously
    FR Wheel ABS Ctrl Status
    		Front wheel RH ABS control status / ON or OFF
    		ON: During control
    		-
    FL Wheel ABS Ctrl Status
    		Front wheel LH ABS control status / ON or OFF
    		ON: During control
    		-
    RR Wheel ABS Ctrl Status
    		Rear wheel RH ABS control status / ON or OFF
    		ON: During control
    		-
    RL Wheel ABS Ctrl Status
    		Rear wheel LH ABS control status / ON or OFF
    		ON: During control
    		-
    RR Wheel EBD Ctrl Status
    		Rear wheel RH EBD control status / ON or OFF
    		ON: During control
    		-
    RL Wheel EBD Ctrl Status
    		Rear wheel LH EBD control status / ON or OFF
    		ON: During control
    		-
    BA Ctrl Status
    		BA control status / ON or OFF
    		ON: During control
    		-
    TRC (TRAC) Ctrl Status
    		TRC control status / ON or OFF
    		ON: During control
    		-
    TRC (TRAC) Engine Ctrl Status
    		TRC engine control status / ON or OFF
    		ON: During control
    		-
    TRC (TRAC) Brake Ctrl Status
    		TRC brake control status / ON or OFF
    		ON: During control
    		-
    FR Wheel VSC Ctrl Status
    		Front wheel RH VSC control status / ON or OFF
    		ON: During control
    		-
    FL Wheel VSC Ctrl Status
    		Front wheel LH VSC control status / ON or OFF
    		ON: During control
    		-
    RR Wheel VSC Ctrl Status
    		Rear wheel RH VSC control status / ON or OFF
    		ON: During control
    		-
    RL Wheel VSC Ctrl Status
    		Rear wheel LH VSC control status / ON or OFF
    		ON: During control
    		-
    Engine Revolutions
    		Engine revolutions / min.: 0 r/min, max.: 65535 r/min
    		-
    		-
    Real Engine Torque
    		Real engine torque / min.: -1024 Nm, max.: 1023 Nm
    		-
    		-
    Accelerator Opening Angle %
    		The difference of a present accelerator / min.: 0%, max.: 128%
    		-
    		-
    Solenoid Relay
    		ABS solenoid relay / ON or OFF
    		ON: Solenoid relay ON
    OFF: Solenoid relay OFF
    		-
    Electronically Controlled Brake System Motor Relay
    		ABS motor relay / ON or OFF
    		ON: Motor relay ON
    OFF: Motor relay OFF
    		-
    Fail Safe Motor Relay
    		ABS motor fail safe relay / ON or OFF
    		ON: Motor relay ON
    OFF: Motor relay OFF
    		-
    TR(A)C/VSC Solenoid (SM2)
    		Master cut solenoid (SM2) / ON or OFF
    		ON: Operates
    		-
    TR(A)C/VSC Solenoid (SM1)
    		Master cut solenoid (SM1) / ON or OFF
    		ON: Operates
    		-
    ABS Solenoid (SFRH)
    		ABS solenoid (SFRH) / ON or OFF
    		ON: Operates
    		-
    ABS Solenoid (SFRR)
    		ABS solenoid (SFRR) / ON or OFF
    		ON: Operates
    		-
    ABS Solenoid (SFLH)
    		ABS solenoid (SFLH) / ON or OFF
    		ON: Operates
    		-
    ABS Solenoid (SFLR)
    		ABS solenoid (SFLR) / ON or OFF
    		ON: Operates
    		-
    ABS Solenoid (SRRH)
    		ABS solenoid (SRRH) / ON or OFF
    		ON: Operates
    		-
    ABS Solenoid (SRRR)
    		ABS solenoid (SRRR) / ON or OFF
    		ON: Operates
    		-
    ABS Solenoid (SRLH)
    		ABS solenoid (SRLH) / ON or OFF
    		ON: Operates
    		-
    ABS Solenoid (SRLR)
    		ABS solenoid (SRLR) / ON or OFF
    		ON: Operates
    		-
    FR Speed Open
    		Front speed sensor RH open detection / ERROR or NORMAL
    		NORMAL
    		-
    FL Speed Open
    		Front speed sensor LH open detection / ERROR or NORMAL
    		NORMAL
    		-
    RR Speed Open
    		Rear speed sensor RH open detection / ERROR or NORMAL
    		NORMAL
    		-
    RL Speed Open
    		Rear speed sensor LH open detection / ERROR or NORMAL
    		NORMAL
    		-
    EFI Communication Open
    		EFI communication open detection / ERROR or NORMAL
    		NORMAL
    		-
    Yaw Rate Open
    		Yaw rate sensor open detection / ERROR or NORMAL
    		NORMAL
    		-
    Deceleration Open
    		Acceleration sensor open detection / ERROR or NORMAL
    		NORMAL
    		-
    Steering Open
    		Steering angle sensor open detection / ERROR or NORMAL
    		NORMAL
    		-
    Master Cylinder Open
    		Master cylinder pressure sensor open detection / ERROR or NORMAL
    		NORMAL
    		-
    IG1 Voltage Value
    		IG1 voltage / min.: 0 V, max.: 255 V
    		11 to 14 V
    		-
    MT Voltage Value
    		MT voltage / min.: 0 V, max.: 255 V
    		-

    TRC/VSC Off Mode
    		VSC OFF switch mode / NORMAL, TRC OFF or VSC OFF
    		NORMAL: Normal mode
    TRC OFF: TRC off mode
    VSC OFF: VSC off mode
    		-
    Number of DTC
    		Number of DTC stored / min.: 0, max.: 255
    		-
    		-
    IG Voltage Value Decreased
    		IG voltage value decrease detection / ERROR or NORMAL
    		NORMAL
    		-
    IG Voltage Value Increased
    		IG voltage value increased detection / ERROR or NORMAL
    		NORMAL
    		-
    FR Speed Sensor Voltage Open
    		Front speed sensor RH voltage open detection / ERROR or NORMAL
    		NORMAL
    		-
    FL Speed Sensor Voltage Open
    		Front speed sensor LH voltage open detection / ERROR or NORMAL
    		NORMAL
    		-
    RR Speed Sensor Voltage Open
    		Rear speed sensor RH voltage open detection / ERROR or NORMAL
    		NORMAL
    		-
    RL Speed Sensor Voltage Open
    		Rear speed sensor LH voltage open detection / ERROR or NORMAL
    		NORMAL
    		-
    M/C Pressure Sensor Noise
    		Master cylinder pressure sensor noise detection / ERROR or NORMAL
    		NORMAL
    		-
    Brake Pedal Switch Open
    		Brake pedal load sensing switch open detection / ERROR or NORMAL
    		NORMAL
    		-
    Yaw Rate Sensor Voltage Open
    		Yaw rate sensor voltage open detection / ERROR or NORMAL
    		NORMAL
    		-
    EFI Communication Invalid
    		EFI communication invalid detection / ERROR or NORMAL
    		NORMAL
    		-


ACTIVE TEST
HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing "Active Tests".

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  7. According to the display on the tester, perform the Active Test.

    ABS/VSC/TRC
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    ABS Warning Light
    		ABS warning light
    		Warning light ON / OFF
    		Observe combination meter
    VSC Warning Light
    		VSC OFF indicator light
    		Indicator light ON / OFF
    		Observe combination meter
    Brake Warning Light
    		Brake warning light
    		Warning light ON / OFF
    		Observe combination meter
    Slip Indicator Light
    		Slip indicator light
    		Indicator light ON / OFF
    		Observe combination meter
    Buzzer
    		Skid control buzzer
    		Buzzer ON / OFF
    		Buzzer can be heard
    Solenoid Relay
    		ABS solenoid relay
    		Relay ON / OFF
    		-
    Motor Relay
    		ABS motor relay
    		Relay ON / OFF
    		Operating sound of motor can be heard
    ABS Solenoid (SRLR)
    		ABS solenoid (SRLR)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRLH)
    		ABS solenoid (SRLH)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRRR)
    		ABS solenoid (SRRR)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SRRH)
    		ABS solenoid (SRRH)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFLR)
    		ABS solenoid (SFLR)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFLH)
    		ABS solenoid (SFLH)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFRR)
    		ABS solenoid (SFRR)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    ABS Solenoid (SFRH)
    		ABS solenoid (SFRH)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC Solenoid (SMR)
    		Master cut solenoid (SM2)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard
    VSC/TRC Solenoid (SMF)
    		Master cut solenoid (SM1)
    		Solenoid ON / OFF
    		Operating sound of solenoid (clicking sound) can be heard