Front Bumper (For Standard) - Installation

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - EXTERIOR PANELS / TRIM

FRONT BUMPER (for Standard) - INSTALLATION

  • HINT:
  • A bolt without a torque specification is shown in the standard bolt chart ().
1. INSTALL FRONT UPPER CENTER BUMPER RETAINER

Install the front upper center bumper retainer with the 3 bolts.

2. INSTALL HEADLIGHT ASSEMBLY LH

for Halogen Headlight:


()

for HID Headlight:


()

3. INSTALL HEADLIGHT ASSEMBLY RH
  • HINT:
  • Use the same procedure described for the LH side.
4. INSTALL FRONT BUMPER SIDE SUPPORT LH

Attach the 3 clips to install the front bumper side support LH.

Install the 2 screws.

5. INSTALL FRONT BUMPER SIDE SUPPORT RH
  • HINT:
  • Use the same procedure described for the LH side.
6. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH

Install the front No. 2 bumper extension sub-assembly LH with the 4 nuts.

  • Torque:
  • 67 N*m{ 683 kgf*cm, 49 ft.*lbf}
7. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH
  • HINT:
  • Use the same procedure described for the LH side.
8. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

Install the front bumper reinforcement sub-assembly with the 6 nuts.

  • Torque:
  • 71 N*m{ 724 kgf*cm, 52 ft.*lbf}
9. INSTALL FRONT BUMPER ENERGY ABSORBER

Install the front bumper energy absorber.

10. INSTALL FRONT BUMPER COVER
  • HINT:
  • For the front bumper cover with garnish, use the procedure described below.
Front Bumper (For Standard) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

w/ Headlight Cleaner System:


Connect the headlight cleaner hose.

w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:


Connect the No. 4 engine room wire connector.

Attach the 10 claws to install the front bumper cover.

Install the 3 clips, 4 screws and 4 bolts.

Using a T30 "TORX" socket, install the 6 screws.

11. INSTALL RADIATOR GRILLE ASSEMBLY

w/ Wide View Front Monitor System:

Connect the connector.

Attach the 2 clips and 8 claws to install the radiator grille assembly.

Install the 3 screws.

12. INSTALL UPPER RADIATOR SUPPORT SEAL

Install the radiator support seal with the 7 clips.

Front Bumper (For Standard) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

13. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Push in the clip to install the front fender splash shield sub-assembly LH.

Install the 3 bolts and screw.

14. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Push in the clip to install the front fender splash shield sub-assembly RH.

Install the 3 bolts and 2 screws.

15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for HID Headlight)
  • NOTICE:
  • When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
16. ADJUST HEADLIGHT AIMING

for Halogen Headlight:

()

for HID Headlight:

()

17. ADJUST FOG LIGHT AIMING (w/ Fog Light)

()


18. INSPECT TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ TOYOTA Parking Assist-sensor System)

()