Front Door Glass Weatherstrip Removal
PRECAUTION
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL
REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
REMOVE DOOR PULL HANDLE
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
REMOVE FRONT DOOR NO. 1 TRIM BRACKET
REMOVE FRONT DOOR SERVICE HOLE COVER LH
REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
REMOVE FRONT DOOR OUTER GLASS WEATHERSTRIP ASSEMBLY LH
Front Door Glass Weatherstrip -- Removal |
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Toyota Fortuner RM000000UYX010X.html).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Toyota Fortuner RM000004W63000X.html).
| 3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL |
Using a moulding remover, detach the 2 clips and 4 claws.
Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.
| 4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH |
Detach the 2 clips and remove the front door lower frame bracket garnish.
Text in Illustration*A
| w/o Front No. 2 Speaker
|
*B
| w/ Front No. 2 Speaker
|
| 5. REMOVE DOOR PULL HANDLE |
Remove the screw and door pull handle.
| 6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH |
Remove the clip and screw.
Detach the 8 clips and remove the front door trim board.
Text in Illustration*1
| Clip
|
*2
| Screw
|
| 7. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH |
Disconnect the mirror connector.
Remove the 3 nuts.
Push down the claw and remove the outer rear view mirror assembly LH.
| 8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH |
Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.
Disconnect the front door inside locking cable and front door lock remote control cable and remove the front door inside handle.
| 9. REMOVE FRONT DOOR NO. 1 TRIM BRACKET |
Remove the 2 screws and front door No. 1 trim bracket.
| 10. REMOVE FRONT DOOR SERVICE HOLE COVER LH |
Pull out the front door inside locking cable, front door lock remote control cable and wire harness from the front door service hole cover, and then remove the front door service hole cover.
- HINT:
- Remove any remaining butyl tape from the front door panel.
| 11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH |
Temporarily install the power window regulator master switch assembly with front door armrest base panel.
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly so that the front door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Toyota Fortuner RM000004W63000X.html).
Remove the power window regulator master switch assembly with front door armrest base panel.
Remove the 2 bolts.
- NOTICE:
- After the bolts are removed, do not allow the front door glass to fall.
Remove the front door glass as indicated by the arrows in the order shown in the illustration.
- NOTICE:
- Do not damage the front door glass.
| 12. REMOVE FRONT DOOR OUTER GLASS WEATHERSTRIP ASSEMBLY LH |
Put protective tape around the front door outer glass weatherstrip.
Text in Illustration*1
| Protective Tape
|
Detach the 5 claws and remove the front door outer glass weatherstrip.
