Rear Door Black Out Tape Removal


  1. PRECAUTION

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

  4. REMOVE DOOR PULL HANDLE

  5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  6. REMOVE REAR DOOR OUTER GLASS WEATHERSTRIP LH

  7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  8. REMOVE REAR DOOR NO. 2 TRIM BRACKET

  9. REMOVE REAR DOOR SERVICE HOLE COVER LH

  10. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  11. REMOVE REAR DOOR GLASS RUN LH

  12. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  14. REMOVE NO. 2 BLACK OUT TAPE LH

Rear Door Black Out Tape -- Removal


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Toyota Fortuner RM000000UYX010X.html).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Toyota Fortuner RM000004W63000X.html).


3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Using a moulding remover, detach the 2 clips and 2 claws.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



4. REMOVE DOOR PULL HANDLE


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Remove the screw and door pull handle.



5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Remove the screw.

  1. Detach the 10 clips and remove the rear door trim board.



6. REMOVE REAR DOOR OUTER GLASS WEATHERSTRIP LH


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Exterior.Rear Door Black Out Tape.Rear Door Black Out Tape Removal

  1. Put protective tape around the rear door outer glass weatherstrip.

    Text in Illustration
    *1
    		Protective Tape

  1. Detach the 4 claws and remove the rear door outer glass weatherstrip.



7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Exterior.Rear Door Black Out Tape.Rear Door Black Out Tape Removal

  1. Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Disconnect the rear door inside locking cable and rear door lock remote control cable and remove the rear door inside handle.



8. REMOVE REAR DOOR NO. 2 TRIM BRACKET


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Remove the 2 screws and rear door No. 2 trim bracket.



9. REMOVE REAR DOOR SERVICE HOLE COVER LH


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Pull out the rear door inside locking cable, rear door lock remote control cable and wire harness from the rear door service hole cover, and then remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the rear door panel.


10. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  1. Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the rear door glass so that the rear door glass channel can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Toyota Fortuner RM000004W63000X.html).

  1. Remove the rear power window regulator switch assembly with rear door armrest base panel.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Partially remove the rear door glass run as shown in the illustration.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Exterior.Rear Door Black Out Tape.Rear Door Black Out Tape Removal

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window division bar may fall and become damaged.
    Text in Illustration
    *1
    		Temporary Bolt

  1. Remove the screw and bolt.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Remove the rear door window division bar together with the rear door glass run as shown in the illustration.

  1. Remove the rear door window division bar from the rear door glass run.



11. REMOVE REAR DOOR GLASS RUN LH


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Remove the front side of the rear door glass run.



12. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Remove the rear door quarter window glass.



13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Remove the rear door glass from the rear door window regulator assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


14. REMOVE NO. 2 BLACK OUT TAPE LH
HINT:
When removing the No. 2 black out tape, heat the vehicle body and No. 2 black out tape using a heat light.
Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
No. 2 Black Out Tape
40 to 60°C (104 to 140°F)
NOTICE:
Do not heat the vehicle body or No. 2 black out tape excessively.


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50

  1. Pull back an edge of the No. 2 black out tape and pull it parallel to the vehicle body to remove it.