Front Power Seat Motor Assembly (For Slide) Installation

Install the slide cable.

NOTICE:

Make sure that the cable is correctly inserted into the motor.

Install the front power seat motor assembly with slide cable to the slide screws.

NOTICE:

1. Make sure that the slide rail is locked in the rearmost position.
   
2. If the serrations on the slide screw and front power seat motor assembly with slide cable do not align, grip the slide screw with needle-nose pliers and install the front power seat motor assembly with slide cable while slightly moving the slide screw. In these cases, do not turn the slide screw 90° or more.
   
3. Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).
   

Using a 4 mm socket hexagon wrench, install the 4 bolts.

Torque:

1.6 N*m{16 kgf*cm, 14 in.*lbf}

Using a 5 mm socket hexagon wrench, install the 2 bolts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Install the new 2 nuts.

Torque:

2.5 N*m{25 kgf*cm, 22 in.*lbf}

Attach the claw to connect the connector to seat frame.

Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1, and then slide the seat and align the matchmarks.

Check that the matchmarks are aligned on both sides.
If the matchmarks are not aligned, check the installation condition of the power seat motor assembly, and remove and reinstall the power seat motor assembly if necessary.

Connect the connector.

Install the seat cushion frame with the 4 bolts.

Torque:

19 N*m{194 kgf*cm, 14 ft.*lbf}

Attach the 4 clamps indicated by the arrows in the illustration to install the seat cushion spring.

w/o Front Seat Side Airbag:
Attach the 2 wire harness clamps.

w/ Front Seat Side Airbag:
Attach the 3 wire harness clamps.

NOTICE:

Be careful not to damage the airbag wire harness or connector.

Attach the hooks to install the seat cushion cover with pad.

Using hog ring pliers, attach the rubber bands of the seatback cover to the seat frame with new hog rings.

NOTICE:

1. Be careful not to damage the cover.
   
2. When installing the hog rings, avoid wrinkling the cover.
   

Install the buckle cover.

Install the front seat inner belt assembly with the nut.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

NOTICE:

Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

Connect the connector and attach the 3 clamps.

Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat cushion inner shield.

Attach the claw to temporarily install the cushion inner shield.

NOTICE:

Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat cushion inner shield.

Attach the guide and claw.

NOTICE:

Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat cushion inner shield.

Install the screw to the cushion inner shield.

Connect the connector.

Install the switch with the 3 screws.

Attach the claw and guide to install the cushion shield.

Install the 3 screws.

Install the 2 screws.

Attach the 4 claws to install the knob.

Attach the 2 claws to install the knob.

Install the front seat assembly (Toyota Fortuner RM000003NZV00FX.html).

Check the SRS warning light (Toyota Fortuner RM000000XFD06DX.html).

Check the power seat operation (Toyota Fortuner RM000003REB000X.html).