Roof Headlining -- Installation |
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1. INSTALL REAR NO. 3 SIDE RAIL SPACER LH |
Attach the 2 claws to install the rear No. 3 side rail spacer.
| 2. INSTALL REAR NO. 3 SIDE RAIL SPACER RH |
- HINT:
- Use the same procedure described for the LH side.
| 3. INSTALL REAR NO. 2 SIDE RAIL SPACER LH |
- HINT:
- Use the same procedure for all No. 2 side rail spacers.
Attach the 2 claws to install the rear No. 2 side rail spacer.
| 4. INSTALL REAR NO. 2 SIDE RAIL SPACER RH |
- HINT:
- Use the same procedure described for the LH side.
| 5. INSTALL SIDE RAIL SPACER (for LHD) |
Attach the 2 claws to install the side rail spacer.
| 6. INSTALL SIDE RAIL SPACER (for RHD, w/o Assist Grip) |
- HINT:
- Use the same procedure described for the LHD.
| 7. INSTALL FRONT SIDE RAIL SPACER LH |
Attach the 2 claws to install the front side rail spacer.
| 8. INSTALL FRONT SIDE RAIL SPACER RH |
- HINT:
- Use the same procedure described for the LH side.
| 9. INSTALL ROOF HEADLINING ASSEMBLY |
 |
Place the roof headlining into the vehicle as shown in the illustration.
- NOTICE:
- Be careful not to damage the roof headlining when placing it.
for LHD:
Attach the 5 fasteners to install the roof headlining.
Install the 7 clips.
Connect the connectors and attach the 4 clamps.
for RHD:
Attach the 5 fasteners to install the roof headlining.
Install the clips.
Text in Illustration *1 w/o Assist Grip - - Connect the connectors and attach the 5 clamps.
Attach the 4 clamps to the front pillar.
| 10. INSTALL DEFROSTER NOZZLE ASSEMBLY |
Attach the 4 clips to install the defroster nozzle assembly.
| 11. INSTALL NO. 3 HEATER TO REGISTER DUCT |
Attach the 4 claws to install the No. 3 heater to register duct.
Install the clip.
| 12. INSTALL NO. 1 HEATER TO REGISTER DUCT |
Attach the 3 claws to install the No. 1 heater to register duct.
Install the clip.
| 13. INSTALL NO. 2 HEATER TO REGISTER DUCT |
Install the No. 2 heater to register duct with the 3 clips.
| 14. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
Attach the 3 guides, 2 claws and 3 clips to install the lower instrument panel finish panel.
| 15. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
| 16. INSTALL ASSIST GRIP |
- HINT:
- Use the same procedure for all assist grips.
Install the assist grip with the 2 screws.
Attach the 4 claws to close the 2 covers.
| 17. INSTALL VISOR HOLDER LH |
Attach the 2 claws to install the visor holder.
Install the screw.
| 18. INSTALL VISOR HOLDER RH |
- HINT:
- Use the same procedure described for the LH side.
| 19. INSTALL VISOR ASSEMBLY LH |
Install the visor with the 2 screws.
Attach the guide.
| 20. INSTALL VISOR ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
| 21. INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
 |
Connect the light connector.
Install the room light with the 2 screws.
Attach the 4 claws to install the lens
| 22. INSTALL COOLER CONTROL SWITCH ASSEMBLY |
Connect the connector.
Attach the 2 clips to install the cooler control switch assembly (rear blower switch) as shown in the illustration.
 |
| 23. INSTALL MAP LIGHT ASSEMBLY |
Connect the connector.
Attach the 2 guides
Install the 2 screws to install the map light assembly.
| 24. INSTALL INNER UPPER ROOF SIDE GARNISH LH |
Attach the clip to install the inner upper roof side garnish.
Install the clip.
Connect the rear No. 2 seat belt shoulder anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to close the rear No. 2 seat belt shoulder anchor cover.
| 25. INSTALL INNER UPPER ROOF SIDE GARNISH RH |
- HINT:
- Use the same procedure described for the LH side.
| 26. INSTALL QUARTER PILLAR GARNISH LH |
Attach the 9 clips to install the quarter pillar garnish.
Connect the rear No. 1 seat belt shoulder anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to close the rear No. 1 seat belt shoulder anchor cover.
| 27. INSTALL QUARTER PILLAR GARNISH RH |
- HINT:
- Use the same procedure described for the LH side.
| 28. INSTALL QUARTER INSIDE TRIM BOARD LH |
Connect the power point socket connector.
Detach the 7 claws and 10 clips to install the quarter inside trim board.
Install the clip.
Connect the rear No. 2 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Connect the rear No. 1 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the outer lap belt anchor cover.
- HINT:
- Use the same procedure for both outer lap belt anchor covers.
| 29. INSTALL QUARTER INSIDE TRIM BOARD RH |
Detach the 8 claws and 10 clips to install the quarter inside trim board.
Install the clip.
Connect the rear No. 2 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Connect the rear No. 1 seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the outer lap belt anchor cover.
- HINT:
- Use the same procedure for both outer lap belt anchor covers.
| 30. INSTALL QUARTER TRIM HOOK |
- HINT:
- Use the same procedure for both quarter trim hooks.
Install the quarter trim hook with the screw.
| 31. INSTALL BACK DOOR SCUFF PLATE |
Attach the 4 claws, 2 guides and 6 clips to install the back door scuff plate.
| 32. INSTALL CENTER PILLAR GARNISH LH |
Attach the guide and clip to install the center pillar garnish.
Connect the front seat belt shoulder anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 4 claws to install the front seat belt shoulder anchor cover.
| 33. INSTALL CENTER PILLAR GARNISH RH |
- HINT:
- Use the same procedure described for the LH side.
| 34. INSTALL LOWER CENTER PILLAR GARNISH LH |
Attach the 2 claws, 2 guides and 2 clips to install the lower center pillar garnish.
Connect the front seat outer belt floor anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the outer lap belt anchor cover.
| 35. INSTALL LOWER CENTER PILLAR GARNISH RH |
- HINT:
- Use the same procedure described for the LH side.
| 36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
 |
Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the rear door opening trim weatherstrip as shown in the illustration.
Text in Illustration *1 Paint Mark *2 Mark Position
| 37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
- HINT:
- Use the same procedure described for the LH side.
| 38. INSTALL REAR DOOR SCUFF PLATE LH |
Attach the 2 clips and 7 claws to install the rear door scuff plate.
| 39. INSTALL REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure described for the LH side.
| 40. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:
Remove the protective cover.
Attach the 2 guides and 2 clips to install the front pillar garnish.
| 41. INSTALL FRONT PILLAR GARNISH RH |
- HINT:
- Use the same procedure described for the LH side.
| 42. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY |
- HINT:
- Use the same procedure for both assist grip.
Install the assist grip with the 2 screws.
| 43. INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH |
- HINT:
- Use the same procedure for both front No. 1 assist grip plugs.
Attach the 2 claws to install the front No. 1 assist grip plug.
| 44. INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH |
- HINT:
- Use the same procedure described for the LH side.
| 45. INSTALL FRONT DOOR OPENING TRIM LH |
 |
Align the paint mark on the front door opening trim with the mark position on the vehicle and install the front door opening trim as shown in the illustration.
Text in Illustration *1 Paint Mark *2 Mark Position
| 46. INSTALL FRONT DOOR OPENING TRIM RH |
- HINT:
- Use the same procedure described for the LH side.
| 47. INSTALL FRONT DOOR SCUFF PLATE LH |
Attach the 3 clips and 7 claws to install the front door scuff plate.
| 48. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedure described for the LH side.
| 49. INSTALL REAR NO. 2 SEAT ASSEMBLY RH |
| 50. INSTALL REAR NO. 2 SEAT ASSEMBLY LH |
- HINT:
- Use the same procedure described for the LH side.
| 51. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Toyota Fortuner RM000004W63000X.html).
| 52. CHECK SRS WARNING LIGHT |