Roof Headlining -- Installation |
| 1. INSTALL SIDE RAIL FRONT SPACER LH |
| 2. INSTALL SIDE RAIL FRONT SPACER RH |
| 3. INSTALL NO. 2 SIDE RAIL REAR SPACER LH |
Install the 4 spacers.
| 4. INSTALL NO. 2 SIDE RAIL REAR SPACER RH |
Install the 4 spacers.
| 5. INSTALL NO. 3 SIDE RAIL REAR SPACER LH |
| 6. INSTALL NO. 3 SIDE RAIL REAR SPACER RH |
| 7. INSTALL NO. 2 ROOF SILENCER PAD |
Install the 3 silencer pads.
| 8. INSTALL ROOF HEADLINING ASSEMBLY |
Install the 6 packings to the roof headlining.
Align the wire harness to the markings, and then install the wire harness with tape.
- NOTICE:
- Attach the roof wire harness securely.
Install the headlining with the 9 clips.
| 9. INSTALL ROOF ASSIST GRIP SUB-ASSEMBLY |
Install the assist grip with the 2 screws.
Attach the 4 claws to install the 2 assist grip plugs.
| 10. INSTALL VISOR HOLDER LH |
Attach the 2 claws to install the holder.
 |
Install the screw.
| 11. INSTALL VISOR HOLDER RH |
- HINT:
- Use the same procedures described for the LH side.
| 12. INSTALL VISOR ASSEMBLY LH |
Install the visor with the 2 screws.
| 13. INSTALL VISOR ASSEMBLY RH |
Install the visor with the 2 screws.
| 14. INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
 |
Connect the light connector.
Install the room light with the 2 screws.
Attach the 4 claws to install the lens
| 15. INSTALL NO. 2 ROOM LIGHT ASSEMBLY |
Connect the light connector.
|
Install the room light with the 2 screws.
Attach the 4 claws to install the lens
| 16. INSTALL MAP LIGHT ASSEMBLY |
 |
Connect the light connector.
Install the map light as shown in the illustration.
Install the 2 screws.
| 17. INSTALL ROOF SIDE INNER UPPER GARNISH LH |
Attach the clip to install the garnish.
 |
Install the clip labeled A.
Connect the rear No. 2 seat belt outer shoulder anchor.
Connect the shoulder anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to close the seat belt anchor cover.
| 18. INSTALL ROOF SIDE INNER UPPER GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 19. INSTALL QUARTER PILLAR GARNISH LH |
Attach the 9 clips to install the garnish.
 |
Connect the rear No. 1 seat belt outer shoulder anchor.
Connect the shoulder anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to close the seat belt anchor cover.
| 20. INSTALL QUARTER PILLAR GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 21. INSTALL REAR POWER POINT SOCKET ASSEMBLY |
 |
Attach the 2 claw fittings to install the socket.
| 22. INSTALL QUARTER INSIDE TRIM BOARD LH |
Install the 2 belt hangers to the trim board.
Connect the power point socket connector.
Attach the 10 clips and 6 claws to install the trim board.
 |
Install the clip labeled A.
Install the quarter trim hook with the screw.
Connect the rear No. 1 seat belt outer anchor.
Connect the anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the lap belt outer anchor cover.
Connect the rear No. 2 seat belt outer anchor.
Connect the anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the lap belt outer anchor cover.
| 23. INSTALL QUARTER TRIM JACK COVER SUB-ASSEMBLY |
| 24. INSTALL AIR OUTLET REGISTER RH |
Attach the claw to install the register.
 |
Install the 5 screws.
| 25. INSTALL COOLER CONTROL SWITCH ASSEMBLY |
Install the control switch with the 2 screws.
 |
Attach the clamp.
| 26. INSTALL QUARTER INSIDE TRIM BOARD RH |
Install the 2 belt hangers to the trim board.
Connect the cooler control switch connector.
Attach the 10 clips and 6 claws to install the trim board.
 |
Install the clip labeled A.
Install the quarter trim hook with the screw.
Connect the rear No. 1 seat belt outer anchor.
Connect the anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the lap belt outer anchor cover.
Connect the rear No. 2 seat belt outer anchor.
Connect the anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the lap belt outer anchor cover.
| 27. INSTALL COOLER CONTROL SWITCH KNOB |
Install the knob to the control switch.
 |
| 28. INSTALL BACK DOOR SCUFF PLATE |
Attach the 6 clips and 4 claws to install the scuff plate.
 |
| 29. INSTALL FRONT PILLAR GARNISH LH |
Attach the 2 clips and 2 claws to install the garnish.
 |
| 30. INSTALL FRONT PILLAR GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 31. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY |
Install the assist grip with the 2 screws.
Attach the 4 claws to install the 2 assist grip plugs.
| 32. INSTALL CENTER PILLAR GARNISH LH |
Attach the claw and clip to install the garnish.
 |
Connect the front seat outer belt's shoulder anchor.
Connect the shoulder anchor with the bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 4 claws to install the seat belt anchor cover cap.
| 33. INSTALL CENTER PILLAR GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 34. INSTALL CENTER PILLAR LOWER GARNISH LH |
Attach the 2 claws and 2 clips to install the garnish.
 |
Connect the front seat outer belt anchor's built-in bolt.
Connect the front seat outer belt anchor's built-in bolt.
- Torque:
- 42 N*m{428 kgf*cm, 31 ft.*lbf}
Attach the 2 claws to install the lap belt outer anchor cover.
 |
| 35. INSTALL CENTER PILLAR LOWER GARNISH RH |
- HINT:
- Use the same procedures described for the LH side.
| 36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
| 37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 38. INSTALL REAR DOOR SCUFF PLATE LH |
Attach the 2 clips and 7 claws to install the scuff plate.
 |
| 39. INSTALL REAR DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 40. INSTALL COWL SIDE TRIM BOARD LH |
Attach the 2 clips to install the trim board.
 |
Install the cap nut.
| 41. INSTALL COWL SIDE TRIM BOARD RH |
- HINT:
- Use the same procedures described for the LH side.
| 42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 44. INSTALL FRONT DOOR SCUFF PLATE LH |
Attach the 3 clips and 7 claws to install the scuff plate.
 |
| 45. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 46. INSTALL REAR NO. 2 SEAT ASSEMBLY |
Install the rear No. 2 seat (Toyota Fortuner RM000001DOI002X.html).
| 47. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |