Vane Pump (For 2Tr-Fe) Inspection

Using a micrometer, measure the diameter (a) of the shaft with pulley.

Using a caliper gauge, measure the inside diameter (b) of the front vane pump housing.

NOTICE:

Do not damage the bushing in the front vane pump housing.

Subtract (a) from (b) to calculate the oil clearance.

Maximum clearance:

0.07 mm (0.0028 in.)

Using a feeler gauge, measure the clearance between the side face of the vane pump rotor groove and the vane pump plates.

Maximum clearance:

0.03 mm (0.0012 in.)

NOTICE:

1. If the clearance is more than the maximum, replace the vane pump plates, vane pump rotor and vane pump cam ring.
   
2. Refer to the following table to select an appropriate combination of vane pump rotor, vane pump cam ring and vane pump plates.
   
   

   Combination of vane pump rotor, vane pump cam ring and vane pump plates:

   
   

   for 2WD

   Vane Pump Rotor Part No.	Vane Pump Cam Ring Part No.	Vane Pump Plate Part No.
   44313-06110	44325-0K010	44345-06110
   44313-06120	44325-0K020	44345-06120
   44313-06130	44325-0K030	44345-06130
   44313-06140	44325-0K040	44345-06140
   44313-06150	44325-0K050	44345-06150

   
   

   for 4WD and Pre-Runner

   Vane Pump Rotor Part No.	Vane Pump Cam Ring Part No.	Vane Pump Plate Part No.
   44313-06110	44325-06160	44345-06110
   44313-06120	44325-06170	44345-06120
   44313-06130	44325-06180	44345-06130
   44313-06140	44325-06190	44345-06140
   44313-06150	44325-06200	44345-06150

Check the flow control valve for leakage. Close one of the holes and apply compressed air of 392 to 490 kPa (4 to 5 kgf/cm², 57 to 71 psi) to the hole on the opposite side. Confirm that the air does not flow out of the end holes.

NOTICE:

Make sure to use clean and dry air.

If there is leakage, replace the flow control valve.

NOTICE:

1. Check the mark on the front vane pump housing and replace the flow control valve with one having the same mark as that of the front vane pump housing.
   
2. Refer to the following table to select an appropriate combination of front vane pump housing and flow control valve.
   
   

   Combination of front vane pump housing and flow control valve:

   
   

   for FF

   Front Vane Pump Housing Mark	Flow Control Valve Mark	Flow Control Valve Part No.
   A	A	44330-0K130
   B	B	44330-0K140
   C	C	44330-0K150
   D	D	44330-0K160
   E	E	44330-0K170
   F	F	44330-0K180

   
   

   for 4WD and Pre-Runner

   Front Vane Pump Housing Mark	Flow Control Valve Mark	Flow Control Valve Part No.
   A	A	44330-0K010
   B	B	44330-0K020
   C	C	44330-0K030
   D	D	44330-0K040
   E	E	44330-0K050
   F	F	44330-0K060

Coat the flow control valve with power steering fluid.

NOTICE:

Make sure to use new power steering fluid.

Insert the flow control valve into the flow control valve installation hole of the front vane pump housing, and check that the flow control valve enters smoothly under its own weight.

If the flow control valve does not enter the front vane pump housing smoothly, replace the flow control valve.

Using a vernier caliper, measure the free length of the flow control valve compression spring.

Minimum free length:

29.2 mm (1.150 in.)

If the union seat in the pressure port union is severely damaged, replace the pressure port union.