Clutch Drum And Input Shaft Assembly Disassembly

Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.

Using a screwdriver, remove the snap ring.

Remove the reverse clutch hub, reverse clutch reaction sleeve, clutch cushion plate, reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the clutch drum.

Remove the reverse clutch reaction sleeve from the reverse clutch hub.

Remove the cushion plate, flange, 5 discs and 4 plate from the reverse clutch hub.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.

Using a dial indicator, measure the inside diameter of the reverse clutch hub bushing.

Standard inside diameter:

35.812 to 35.837 mm (1.4099 to 1.4109 in.)

Maximum inside diameter:

35.887 mm (1.4129 in.)

1. If the inside diameter is greater than the maximum, replace the reverse clutch hub.
   

Remove the forward clutch hub from the clutch drum.

Remove the 2 thrust needle roller bearings from the forward clutch hub.

Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

Standard inside diameter:

26.037 to 26. 062 mm (1.0251 to 1.0261 in.)

Maximum inside diameter:

26.112 mm (1.028 in.)

1. If the inside diameter is greater than the maximum, replace the forward clutch hub.
   

Remove the multiple disc clutch hub from the clutch drum.

Remove the No. 2 thrust bearing race and input shaft thrust bearing race rear from the multiple disc clutch hub.

Remove the thrust needle roller bearing from the clutch drum.

Remove the input shaft from the clutch drum.

Remove the 3 oil seal rings from the input shaft.

Using a screwdriver, remove the hole snap ring

Remove the 2 flanges, 6 discs and 5 plates from the input shaft.

Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

NOTICE:

Before assembling new discs, soak them in ATF for at least 15 minutes.

Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

SST

09350-30020(09350-07040,09350-07070)

Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.

Remove the O-ring from the No. 1 clutch balancer.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

26.74 mm (1.053 in.)

Holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm², 57 psi) to the input shaft to remove the forward clutch piston.

Remove the 2 O-rings from the forward clutch piston.

Remove the reverse clutch flange from the clutch drum.

Using a screwdriver, remove the 2 hole snap rings from the clutch drum.

Remove the flange, 5 discs and 6 plates from the clutch drum.

Place SST on the No. 3 clutch balancer, and compress the return spring with a press.

SST

09387-00070
09350-30020(09350-07070)

Remove the snap ring and clutch balancer.

Remove the reverse clutch return spring and O-ring from the reverse clutch piston.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.04 mm (0.828 in.)

Remove the reverse clutch piston sub-assembly from the clutch drum.

Remove the O-ring from the reverse clutch piston.

Remove the O-ring from the clutch drum.

Place SST on the direct clutch piston, and compress the return spring with a press.

SST

09320-89010
09350-30020(09350-07070)

Using 2 screwdrivers, remove the direct clutch piston from the clutch drum.

Remove the O-ring from the clutch drum.

Remove the No. 2 clutch balancer and direct clutch return spring from the direct clutch piston sub-assembly.

Remove the 2 O-rings from the direct clutch piston.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

19.51 mm (0.768 in.)