Dtc P0010/39 Camshaft Position A Actuator Circuit (Bank 1)


DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

When using intelligent tester:

PERFORM ACTIVE TEST (OPERATE OCV)

CHECK CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV SIGNAL)

CHECK ECM (OCV SIGNAL)

When not using intelligent tester:

CHECK CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OPERATE OCV)

CHECK ECM (OCV SIGNAL)

CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE (OCV) - ECM)

DTC P0010/39 Camshaft Position "A" Actuator Circuit (Bank 1)


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller. The ECM sends a target "duty-cycle" control signal to the OCV. This control signal, applied to the OCV, regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed based on engine operation conditions, such as intake air volume, throttle position and engine coolant temperature.
The ECM controls the OCV based on the signals from several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative position between the camshaft and crankshaft is optimized, the engine torque and the fuel economy improve, and the exhaust emission drops. The ECM detects the actual valve timing using signals from the camshaft position sensor and crankshaft position sensor. The ECM then performs feedback control and verifies target valve timing.

Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.2Tr-Fe Engine Control System.Sfi System. Dtc P0010/39 Camshaft Position A Actuator Circuit (Bank 1)


DTC No.
DTC Detection Condition
Trouble Area
P0010/39
Open or short in oil control valve circuit
(1 trip detection logic)
  1. Open or short in oil control valve circuit
  2. OCV
  3. ECM

MONITOR DESCRIPTION

After the ECM sends the "target" duty-cycle signal to the OCV, the ECM monitors the OCV current to establish an "actual" duty-cycle. The ECM detects a malfunction and sets a DTC when the actual duty-cycle ratio varies from the target duty-cycle ratio.
This monitor runs for 1 second (the first second of engine idle) after the engine is started.

WIRING DIAGRAM


Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.2Tr-Fe Engine Control System.Sfi System. Dtc P0010/39 Camshaft Position A Actuator Circuit (Bank 1)


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

When using intelligent tester:

1.PERFORM ACTIVE TEST (OPERATE OCV)

  1. Start and warm up the engine.

  1. Turn the ignition switch OFF.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VVT System (Bank 1).

  1. Using the intelligent tester, operate the OCV and check the engine speed.

    OK:
    Tester Operation
    		Specified Condition
    OCV is OFF
    		Normal engine speed
    OCV is ON
    		Rough idle or engine stall


OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.CHECK CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV SIGNAL)
Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.2Tr-Fe Engine Control System.Sfi System. Dtc P0010/39 Camshaft Position A Actuator Circuit (Bank 1)

  1. Disconnect the C2 OCV connector.

  1. While idling the engine, check the waveform of the OCV connector using an oscilloscope.

    OK:
    Tester Connection
    		Specified Condition
    C2-2 (OC1+) - C2-1 (OC1-)
    		Correct waveform is as shown
    Tool Setting
    		Condition
    5 V/DIV., 1 msec./DIV.
    		Accelerate slowly after engine warm-up


OK
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
NG


3.CHECK ECM (OCV SIGNAL)
Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.2Tr-Fe Engine Control System.Sfi System. Dtc P0010/39 Camshaft Position A Actuator Circuit (Bank 1)

  1. While idling the engine, check the waveform of the ECM connector using an oscilloscope.

    OK:
    Tester Connection
    		Specified Condition
    E11-13 (OC1+) - E11-12 (OC1-)
    		Correct waveform is as shown
    Tool Setting
    		Condition
    5 V/DIV., 1 msec./DIV.
    		Accelerate slowly after engine warm-up


NG
REPLACE ECM
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


When not using intelligent tester:

1.CHECK CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OPERATE OCV)
Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.2Tr-Fe Engine Control System.Sfi System. Dtc P0010/39 Camshaft Position A Actuator Circuit (Bank 1)

  1. Disconnect the C2 OCV connector.

  1. Apply positive (+) battery voltage between the terminals of the OCV.

  1. Check the engine speed.

    OK:
    Rough idle or engine stalls.


NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
OK


2.CHECK ECM (OCV SIGNAL)
Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.2Tr-Fe Engine Control System.Sfi System. Dtc P0010/39 Camshaft Position A Actuator Circuit (Bank 1)

  1. While idling the engine, check the waveform of the ECM connector using an oscilloscope.

    OK:
    Tester Connection
    		Specified Condition
    E11-13 (OC1+) - E11-12 (OC1-)
    		Correct waveform is as shown
    Tool Setting
    		Condition
    5 V/DIV., 1 msec./DIV.
    		Accelerate slowly after engine warm-up


NG
REPLACE ECM
OK


3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE (OCV) - ECM)
Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.2Tr-Fe Engine Control System.Sfi System. Dtc P0010/39 Camshaft Position A Actuator Circuit (Bank 1)

  1. Disconnect the C2 OCV connector.

  1. Disconnect the E11 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    		Specified Condition
    C2-2 - E11-13 (OC1+)
    		Below 1 Ω
    C2-1 - E11-12 (OC1-)
    		Below 1 Ω
    C2-2 or E11-13 (OC1+) - Body ground
    		10 kΩ or higher
    C2-1 or E11-12 (OC1-) - Body ground
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS