Dtc C1403 Rear Speed Sensor Rh Malfunction


DESCRIPTION

INSPECTION PROCEDURE

CHECK REAR SPEED SENSOR INSTALLATION

INSPECT REAR SPEED SENSOR TIP

INSPECT REAR SKID CONTROL ROTOR

READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

REPLACE REAR SPEED SENSOR

RECONFIRM DTC

DTC C1403 Rear Speed Sensor RH Malfunction

DTC C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC C1404 Rear Speed Sensor LH Malfunction


DESCRIPTION

Refer to DTCs C1401 and C1402 (Toyota Fortuner RM000000XI90JJX.html).

DTC Code
DTC Detection Condition
Trouble Area
C1403
C1404
One of the following conditions is met:
  1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage from one of the speed sensors is below that of the other sensors for 15 seconds or more.
  2. At a vehicle speed of less than 10 km/h (6 mph), the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
  3. At a vehicle speed of less than 10 km/h (6 mph), the outputs from both rear speed sensors are 0 km/h (0 mph) for a cumulative time of 200 seconds.
  1. Rear speed sensor RH/LH
  2. Rear skid control rotor RH/LH
  3. Sensor installation
C1273
C1274
Stored during Test Mode.
  1. Rear speed sensor RH/LH
  2. Rear skid control rotor RH/LH
  3. Sensor installation
HINT:
  1. DTCs C1403 and C1273 are for the rear speed sensor RH.
  2. DTCs C1404 and C1274 are for the rear speed sensor LH.

INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal after cleaning or replacement (Toyota Fortuner RM000000XHT08TX.html).
1.CHECK REAR SPEED SENSOR INSTALLATION

  1. Turn the ignition switch off.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C1403 Rear Speed Sensor Rh Malfunction

  1. Check the speed sensor installation (Toyota Fortuner RM0000010JQ020X.html).

    Text in Illustration
    *1
    		Rear Speed Sensor
    *a
    		No clearance
    *b
    		CORRECT
    *c
    		INCORRECT
    OK:
    There is no clearance between the sensor and rear axle housing.
    The installation bolt is tightened properly.


NG
INSTALL REAR SPEED SENSOR CORRECTLY (Toyota Fortuner RM0000010JQ020X.html)
OK


2.INSPECT REAR SPEED SENSOR TIP

  1. Turn the ignition switch off.

  1. Remove the rear speed sensor (Toyota Fortuner RM0000010JT01OX.html).

  1. Check the rear speed sensor tip.

    OK:
    No scratches, oil or foreign matter on the sensor tip.
    NOTICE:
    Do not replace the speed sensor if no damage to the speed sensor tip is found.
    HINT:
    1. If the sensor is contaminated with oil or other foreign material, clean the sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.


NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


3.INSPECT REAR SKID CONTROL ROTOR

  1. Turn the ignition switch off.

  1. Remove the rear axle shaft with backing plate (Toyota Fortuner RM000000ZZV00LX.html).

  1. Check the rear skid control rotor.

    OK:
    No scratches, oil or foreign matter on the rotor.


NG
CLEAN OR REPLACE REAR SKID CONTROL ROTOR
OK


4.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    RR Wheel Speed
    		Rear speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual wheel speed
    		No large fluctuations when driving at a constant speed.
    RL Wheel Speed
    		Rear speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    		Actual wheel speed
    		No large fluctuations when driving at a constant speed.

  1. Check the speed value output from the speed sensor displayed on the intelligent tester.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Toyota Fortuner RM0000011JB00WX.html).
    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Toyota Fortuner RM0000012Q9013X.html)

5.REPLACE REAR SPEED SENSOR

  1. Turn the ignition switch off.

  1. Replace the rear speed sensor (Toyota Fortuner RM0000010JT01OX.html).


NEXT


6.RECONFIRM DTC

  1. Clear the DTCs (Toyota Fortuner RM000000XHV0C7X.html).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Toyota Fortuner RM000000XHV0C7X.html).

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC is output
    		B


B
REPLACE REAR SKID CONTROL ROTOR (Toyota Fortuner RM000000ZZV00LX.html)
A

END