Audio And Visual System (For Radio And Display Type) Steering Pad Switch Circuit
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
INSPECT STEERING PAD SWITCH ASSEMBLY
INSPECT SPIRAL CABLE SUB-ASSEMBLY
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - SPIRAL CABLE)
AUDIO AND VISUAL SYSTEM (for Radio and Display Type) - Steering Pad Switch Circuit |
DESCRIPTION
This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and the radio and display receiver assembly itself cannot function.
WIRING DIAGRAM
INSPECTION PROCEDURE
- CAUTION:
- The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Toyota Fortuner RM000000KT10ELX.html).
| 1.INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly (Toyota Fortuner RM0000033RT068X.html).
Text in Illustration*A
| w/ Multi-information Display
| -
| -
|
*1
| Volume+ Switch
| *2
| Volume- Switch
|
*3
| Seek- Switch
| *4
| Seek+ Switch
|
*5
| MODE Switch
| *6
| On Hook Switch
|
*7
| Off Hook Switch
| -
| -
|
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Switch Condition
| Specified Condition
|
10 (AU1) - 8 (EAU)
| No switch is pushed
| 95 to 105 kΩ
|
Seek+ switch is pushed
| Below 2.5 Ω
|
Seek- switch is pushed
| 312.6 to 345.5 Ω
|
Volume+ switch is pushed
| 950 to 1050 Ω
|
Volume- switch is pushed
| 2954.5 to 3265.5 Ω
|
9 (AU2) - 8 (EAU)
| No switch is pushed
| 95 to 105 kΩ
|
MODE switch is pushed
| Below 2.5 Ω
|
On Hook switch is pushed
| 312.6 to 345.5 Ω
|
Off Hook switch is pushed
| 950 to 1050 Ω
|
| 2.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Remove the spiral cable sub-assembly (Toyota Fortuner RM0000010B2003X.html).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
8 (EAU) - 4 (EAU)
| Spiral cable is turned 2.5 rotations counterclockwise
| Below 1 Ω
|
Spiral cable is centered
|
Spiral cable is turned 2.5 rotations clockwise
|
10 (AU1) - 6 (AU1)
| Spiral cable is turned 2.5 rotations counterclockwise
|
Spiral cable is centered
|
Spiral cable is turned 2.5 rotations clockwise
|
9 (AU2) - 5 (AU2)
| Spiral cable is turned 2.5 rotations counterclockwise
|
Spiral cable is centered
|
Spiral cable is turned 2.5 rotations clockwise
|
Text in Illustration*a
| Steering Pad Switch Side
|
*b
| Vehicle Side
|
- CAUTION:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Toyota Fortuner RM000000KT10ELX.html).
| 3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - SPIRAL CABLE) |
Disconnect the R19 radio and display receiver assembly connector.
Disconnect the S30 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
| Condition
| Specified Condition
|
R19-21 (SW1) - S30-6 (AU1)
| Always
| Below 1 Ω
|
R19-22 (SW2) - S30-5 (AU2)
|
R19-23 (SWG) - S30-4 (EAU)
|
R19-21 (SW1) - Body ground
| Always
| 10 kΩ or higher
|
R19-22 (SW2) - Body ground
|
R19-23 (SWG) - Body ground
|
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
