Dtc C0200/31 Front Speed Sensor Rh Circuit


DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

PERFORM TEST MODE (SIGNAL CHECK)

RECONFIRM DTC

CHECK IF SKID CONTROL ECU AND FRONT SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED

RECONFIRM DTC

CHECK FRONT SPEED SENSOR INSTALLATION

CHECK FRONT SPEED SENSOR TIP

INSPECT FRONT SPEED SENSOR

CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

INSPECT SKID CONTROL ECU (SENSOR INPUT)

REPLACE FRONT SPEED SENSOR

RECONFIRM DTC

REPLACE FRONT SKID CONTROL ROTOR

RECONFIRM DTC

DTC C0200/31 Front Speed Sensor RH Circuit

DTC C0205/32 Front Speed Sensor LH Circuit

DTC C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC)


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU. The speed sensor has a magnet behind its detection terminal, and detects changes in magnetic flux density between the peaks and valleys of the magnetic rotor teeth.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS.
DTCs C1271/71 and C1272/72 are deleted when the speed sensor sends a vehicle speed signal or Test Mode ends. DTCs C1271/71 and C1272/72 are output only in Test Mode.
HINT:
When the connectors between the speed sensor and skid control ECU are connected, the following waveform is output.

Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C0200/31 Front Speed Sensor Rh Circuit


DTC Code
DTC Detection Condition
Trouble Area
C0200/31
C0205/32
When one of the following conditions is met:
  1. At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of the sensor signal occurs 255 times or more.
  3. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  4. With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases and stays at or below a certain value for 0.5 seconds or more.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Front skid control rotor RH/LH
  4. Sensor installation
  5. Skid control ECU (Brake actuator assembly)
C1271/71
C1272/72
Detected only during Test Mode.
  1. Front speed sensor RH/LH
  2. Sensor installation
  3. Front skid control rotor RH/LH
HINT:
  1. DTCs C0200/31 and C1271/71 are for the front speed sensor RH.
  2. DTCs C0205/32 and C1272/72 are for the front speed sensor LH.

WIRING DIAGRAM


Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C0200/31 Front Speed Sensor Rh Circuit


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Toyota Fortuner RM000000XHR02TX.html).
  2. Check the speed sensor signal in test mode after replacing parts or clearing DTCs (Toyota Fortuner RM000000XHT070X.html).
1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

  1. Using the intelligent tester, check for any momentary interruption in the wire harnesses and connectors corresponding to the DTC (Toyota Fortuner RM000000XHS04KX.html).

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    FR Speed Open
    		Front speed sensor RH open detection / Error or Normal
    		Normal
    		-
    FL Speed Open
    		Front speed sensor LH open detection / Error or Normal
    		Normal
    		-
    OK:
    Normal (There are no momentary interruptions.)
    HINT:
    Perform the above inspection before removing the sensor and connector.


NG
Go to step 5
OK


2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Data List mode on the intelligent tester (Toyota Fortuner RM000000XHW080X.html).

    ABS/VSC/TRC
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    FR Wheel Speed
    		Front wheel RH speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    		Actual wheel speed
    		Similar to speed indicated on speedometer
    FL Wheel Speed
    		Front wheel LH speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    		Actual wheel speed
    		Similar to speed indicated on speedometer

  1. Check that there is no significant difference between the speed value displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Toyota Fortuner RM0000011JB00MX.html).
    OK:
    The speed value output displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NG
Go to step 7
OK


3.PERFORM TEST MODE (SIGNAL CHECK)

  1. Perform the sensor check in the Test Mode procedure (Toyota Fortuner RM000000XHT070X.html).

    OK:
    All Test Mode DTCs are erased.


NG
Go to step 7
OK


4.RECONFIRM DTC

  1. Clear the DTC(s) (Toyota Fortuner RM000000XHV09NX.html).

  1. Start the engine.

  1. Drive the vehicle at a speed of 30 km/h (19 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Toyota Fortuner RM000000XHV09NX.html).

    Result
    Result
    		Proceed to
    DTC not output
    		A
    DTC output
    		B


B
Go to step 12
A

CHECK FOR INTERMITTENT PROBLEMS

5.CHECK IF SKID CONTROL ECU AND FRONT SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED

  1. Check if the skid control ECU and front speed sensor connectors are securely connected.


NEXT


6.RECONFIRM DTC

  1. Clear the DTC(s) (Toyota Fortuner RM000000XHV09NX.html).

  1. Start the engine.

  1. Drive the vehicle at a speed of 30 km/h (19 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Toyota Fortuner RM000000XHV09NX.html).

    Result
    Result
    		Proceed to
    DTC output
    		A
    DTC not output
    		B


B
END
A


7.CHECK FRONT SPEED SENSOR INSTALLATION


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C0200/31 Front Speed Sensor Rh Circuit

  1. Turn the ignition switch off.

  1. Check the speed sensor installation (Toyota Fortuner RM0000010JM01NX.html).

    OK:
    The installation bolt is tightened properly and there is no clearance between the speed sensor and knuckle.


NG
INSTALL FRONT SPEED SENSOR CORRECTLY
OK


8.CHECK FRONT SPEED SENSOR TIP

  1. Remove the front speed sensor (Toyota Fortuner RM0000010JP015X.html).

  1. Check the speed sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.
    HINT:
    1. If the sensor is contaminated with oil or other foreign material, clean the sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
    NOTICE:
    1. Do not replace the speed sensor if no damage to the speed sensor tip is found.
    2. Check the speed sensor signal after cleaning or replacement (Toyota Fortuner RM000000XHT070X.html).


NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


9.INSPECT FRONT SPEED SENSOR


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C0200/31 Front Speed Sensor Rh Circuit

  1. Install the front speed sensor.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    		Condition
    		Specified Condition
    1 (FR+) - Body ground
    		Always
    		10 kΩ or higher
    2 (FR-) - Body ground
    		Always
    		10 kΩ or higher
    for LH:
    Tester Connection
    		Condition
    		Specified Condition
    1 (FL+) - Body ground
    		Always
    		10 kΩ or higher
    2 (FL-) - Body ground
    		Always
    		10 kΩ or higher
    NOTICE:
    Check the speed sensor signal after replacement (Toyota Fortuner RM000000XHT070X.html).


NG
REPLACE FRONT SPEED SENSOR
OK


10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)


  1. Disconnect the skid control ECU connector.


    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C0200/31 Front Speed Sensor Rh Circuit

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    		Condition
    		Specified Condition
    S25-7 (FR+) - S5-1 (FR+)
    		Always
    		Below 1 Ω
    S25-7 (FR+) - Body ground
    		Always
    		10 kΩ or higher
    S25-6 (FR-) - S5-2 (FR-)
    		Always
    		Below 1 Ω
    S25-6 (FR-) - Body ground
    		Always
    		10 kΩ or higher
    for LH:
    Tester Connection
    		Condition
    		Specified Condition
    S25-19 (FL+) - S4-1 (FL+)
    		Always
    		Below 1 Ω
    S25-19 (FL+) - Body ground
    		Always
    		10 kΩ or higher
    S25-18 (FL-) - S4-2 (FL-)
    		Always
    		Below 1 Ω
    S25-18 (FL-) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT SKID CONTROL ECU (SENSOR INPUT)

  1. Connect the skid control ECU connector.



    Toyota Fortuner. Ggn50, 60 Kun51, 61 Tgn51 Lan50.Brake Control.Vehicle Stability Control System. Dtc C0200/31 Front Speed Sensor Rh Circuit

  1. Disconnect the front speed sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    		Switch Condition
    		Specified Condition
    S5-1 (FR+) - Body ground
    		Ignition switch ON
    		8 to 14 V
    for LH:
    Tester Connection
    		Switch Condition
    		Specified Condition
    S4-1 (FL+) - Body ground
    		Ignition switch ON
    		8 to 14 V


NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


12.REPLACE FRONT SPEED SENSOR

  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Toyota Fortuner RM0000010JP015X.html).

    NOTICE:
    Check the speed sensor signal after replacement (Toyota Fortuner RM000000XHT070X.html).

NEXT


13.RECONFIRM DTC

  1. Clear the DTC(s) (Toyota Fortuner RM000000XHV09NX.html).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Toyota Fortuner RM000000XHV09NX.html).

    Result
    Result
    		Proceed to
    DTC output
    		A
    DTC not output
    		B


B
END
A


14.REPLACE FRONT SKID CONTROL ROTOR

  1. Turn the ignition switch off.

  1. Replace the front skid control rotor (Toyota Fortuner RM00000112M005X.html).

    NOTICE:
    Check the speed sensor signal after replacement (Toyota Fortuner RM000000XHT070X.html).

NEXT


15.RECONFIRM DTC

  1. Clear the DTC(s) (Toyota Fortuner RM000000XHV09NX.html).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Toyota Fortuner RM000000XHV09NX.html).

    Result
    Result
    		Proceed to
    DTC not output
    		A
    DTC output
    		B
    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Toyota Fortuner RM000000XHN092X.html).


B
REPLACE BRAKE ACTUATOR ASSEMBLY
A

END