Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SEAT
REAR SEATBACK HEATER (for 60/40 Split Seat Type 40 Side) - INSTALLATION
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
| 1. INSTALL REAR SEATBACK HEATER ASSEMBLY |
Set the seatback heater with the name stamp side facing the seatback cover.
Install the seatback heater with new tack pins.
| 2. INSTALL REAR SEPARATE TYPE SEATBACK COVER |
Using hog ring pliers, install the seatback cover with new hog rings.
- NOTICE:
w/ Rear Seat Side Airbag:
Connect the seatback cover bracket to the seatback pad.
| 3. INSTALL SEATBACK COVER WITH PAD |
Install the seatback cover with pad.
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seatback.
w/ Seat Heater System:
Pass the seatback heater wire harness through the hole in the seatback.
Connect the seatback heater wire harness and install a new cable tie.
w/ Rear Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the cap nut.
- Torque:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
- CAUTION:
- After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
Using hog ring pliers, install new hog rings to the seatback frame.
| 4. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
Attach the 4 claws to install the 2 supports.
| 5. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 6. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH |
Push the board down to attach the 2 claws on the bottom.
Attach the 2 claws on the top of the board to install it.
| 7. INSTALL REAR SEATBACK COVER |
Attach the 4 claws to install the cover.
| 8. INSTALL SEAT CUSHION COVER WITH PAD |
Install the seat cushion cover with pad.
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seat cushion.
w/ Seat Heater System:
Pass the seatback heater wire harness through the hole in the seat cushion.
Connect the 2 seat heater connectors.
w/ Rear Seat Side Airbag:
Attach the side airbag wire harness clamps.
| 9. INSTALL REAR SEAT UNDER TRAY COVER RH |
Attach the 4 claws to install the cover.
Install the 2 screws.
| 10. INSTALL REAR UNDER SIDE COVER LH |
Attach the 2 claws and clip to install the cover.
Install the 5 screws.
| 11. INSTALL REAR SEAT COVER |
Attach the 2 claws to install the cover.
Install the 3 screws.
Attach the 12 claws.
| 12. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH |
Attach the cable clamp to connect the cable.
Install the hinge with the 2 nuts.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
w/ Rear Seat Side Airbag:
Attach the wire harness clamp.
w/ Seat Heater System:
Attach the wire harness clamp.
| 13. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH |
Install the hinge with the 2 nuts.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
| 14. INSTALL REAR NO. 2 SEAT PROTECTOR |
Install the wire harness, and attach the 2 claws to close the protector.
Attach the claw to install the protector to the seat hinge.
Install the clip.
w/ Rear Seat Side Airbag:
Attach the claw to install the wire harness connector.
w/ Seat Heater System:
Attach the claw to install the wire harness connector.
| 15. INSTALL REAR NO. 2 SEAT LEG SIDE COVER |
Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.
Attach the 3 claws to install the seat leg side cover.
Install the 4 screws.
| 16. INSTALL UPPER SEAT TRACK RAIL COVER RH |
Attach the 2 claws to install the cover.
| 17. INSTALL UPPER SEAT TRACK RAIL COVER LH |
Attach the 2 claws to install the cover.
| 18. INSTALL REAR NO. 1 SEAT RECLINING COVER LH |
Attach the 4 claws to install the cover.
Install the 2 screws.
| 19. INSTALL REAR NO. 1 SEAT RECLINING COVER RH |
Attach the 3 claws in the order shown in the illustration to install the cover.
Install the 2 screws.
| 20. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH |
Install the release handle with the screw.
| 21. INSTALL SEAT ADJUSTER BOLT COVER |
Attach the 2 claws to install the cover.
| 22. INSTALL REAR NO. 1 SEAT ASSEMBLY RH |
Install the rear No. 1 seat assembly ().