Rear Door Lock - Installation

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - DOOR LOCK

REAR DOOR LOCK - INSTALLATION

  • HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the rear door inside locking cable assembly LH.

Text in Illustration
*Aw/o Double Lock
*Bw/ Double Lock
Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 3 claws.

2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

Install the rear door lock remote control cable assembly LH.

Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the claw.

3. INSTALL REAR DOOR LOCK ASSEMBLY LH
Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Apply MP grease to the sliding parts of the rear door lock assembly.

Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

Using a T30 ''TORX'' wrench, the 3 screws.

  • Torque:
  • 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}
4. INSTALL REAR DOOR SERVICE HOLE COVER LH

Apply butyl tape to the door.

Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.

  • NOTICE:
When installing the rear door service hole cover LH, pull the links and connectors through the rear door service hole cover LH.
There should be no wrinkles or folds after attaching the rear door service hole cover LH.
After attaching the rear door service hole cover LH, check the sealing quality.

Connect the 2 connectors.

Attach the 6 clamps.

Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the bolt as shown in the illustration.

  • Torque:
  • 8.4 N*m{ 86 kgf*cm, 74 in.*lbf}
5. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Connect the connector.

Attach the claw of the courtesy light to the rear door trim.

6. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Connect the connector.

Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH to the rear door inside handle sub-assembly LH.

Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 4 claws and 9 clips to install the rear door trim board sub-assembly LH.

Install the 3 screws.

7. INSTALL ASSIST GRIP COVER LH

Attach the 9 claws to install the assist grip cover LH to the rear door trim board sub-assembly LH.

8. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

Install the rear door inside handle bezel LH to the trim board with the 6 screws.

9. INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

Connect the connector.

Rear Door Lock - Installation. DOOR LOCK. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 7 claws to install the armrest base panel.

10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
  • NOTICE:
  • When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().