Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SEAT
LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Manual Seat) - INSTALLATION
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
| 1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar support) |
Install the lumbar support adjuster with the 2 screws.
Connect the lumbar support adjuster connector.
Attach the 4 hooks to install the seatback spring.
Connect the active headrest cable with the cable clamp.
Install the 4 springs.
| 2. INSTALL SEATBACK COVER WITH PAD |
Set the seatback cover with pad in place.
w/ Seatback Board:
w/ Front Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the nut.
- Torque:
- 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}
- CAUTION:
- After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
Attach the 9 hooks.
Using hog ring pliers, install new hog rings.
- NOTICE:
w/o Seatback Board:
Attach the 4 claws to install the 2 headrest supports.
w/ Front Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the nut.
- Torque:
- 5.0 N*m{ 51 kgf*cm, 44 in.*lbf}
- CAUTION:
- After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
Close the 2 fasteners.
Using hog ring pliers, install new hog rings.
- NOTICE:
| 3. INSTALL FRONT SEAT HEADREST SUPPORT (w/ Active Headrest) |
Attach the 4 claws to install the 2 front seat headrest supports.
| 4. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board) |
Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.
Install the 2 screws.
| 5. INSTALL FRONT INNER SEAT CUSHION SHIELD LH |
Attach the claw and clip to install the front inner seat cushion shield LH.
Install the screw.
| 6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH |
Install the front seat belt anchor plate.
Install the front seat inner belt assembly with the nut.
- Torque:
- 42 N*m{ 428 kgf*cm, 31 ft.*lbf}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connectors and attach the clamps.
| 7. INSTALL FRONT SEAT CUSHION SHIELD LH |
w/ Lumbar Support:
Connect the lumbar switch connector.
for 4 Way Seat Type:
Attach the 3 claws in the order shown in the illustration to install the front seat cushion shield LH.
Install the 2 screws.
for 8 Way Seat Type:
Attach the 3 claws in the order shown in the illustration to install the front seat cushion shield LH.
Install the 3 screws.
w/ Seatback Board:
Connect the 2 rubber bands to the 2 hooks.
w/o Seatback Board:
Connect the rubber band to the 2 hooks.
| 8. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH |
Attach the claw to install the reclining adjuster release handle LH.
| 9. INSTALL VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type) |
Install the snap ring to the vertical seat adjuster knob.
Install the vertical seat adjuster knob.
| 10. INSTALL VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type) |
Install the vertical adjusting handle with the 2 screws.
| 11. INSTALL VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type) |
Attach the 2 claws to install the vertical adjuster cover LH.
| 12. INSTALL FRONT SEAT ASSEMBLY LH |
Install the front seat assembly ().