Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - SUPPLEMENTAL RESTRAINT SYSTEMS
FRONT PASSENGER AIRBAG ASSEMBLY - DISPOSAL
- HINT:
- When scrapping a vehicle equipped with the SRS or disposing of the steering pad, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of DISTRIBUTOR.
- CAUTION:
1. DISPOSE OF FRONT PASSENGER AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE) |
- HINT:
- Prepare a battery as the power source to deploy the airbag.

Check the function of SST ().
Read the precaution ().
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
Remove the front passenger airbag ().

Install SST.
Disconnect the connector.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Connect SST connector to the instrument panel wire.
- SST
- 09082-00700
09082-00780
- NOTICE:
- To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock.

Move SST at least 10 m (32.8 ft.) away from the vehicle front side window.
Maintaining enough clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.
- NOTICE:
- Take care not to damage SST wire harness.
Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
Press SST activation switch to deploy the airbag.
- CAUTION:
- HINT:
- The airbag is deployed as the LED of SST activation switch comes on.
2. DISPOSE OF FRONT PASSENGER AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE) |
- NOTICE:
- Be sure to follow the procedure detailed below when deploying the airbag.
- HINT:
- Prepare a battery as the power source to deploy the airbag.

Check the function of SST ().
Remove the front passenger airbag ().
- CAUTION:

Install SST.
After connecting SST to each other, connect them to the front passenger airbag.
- SST
- 09082-00802(09082-10801,09082-30801)

Using a service-purpose wire harness for the vehicle, tie down the front passenger airbag to a tire.
- Cross-sectional area of stripped wire harness section:
- 1.25 mm2 (0.00192 in.2) or more
- CAUTION:
- If the wire harness is too thin or an alternative object is used to tie down the front passenger airbag, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).
- HINT:
- To calculate the cross-sectional area of the stripped wire harness section: Cross-sectional area:
- Area = 3.14 x (Diameter)2 divided by 4
Position the front passenger airbag inside a tire with the airbag deployment side facing inside.
- Tire size:
- Must exceed the following dimensions
- Width:
- 185 mm (7.28 in.)
- Inner diameter:
- 360 mm (14.2 in.)
Tie the front passenger airbag to the tire with several wire harnesses.
- CAUTION:
- NOTICE:
- As the tire may be damaged by the airbag deployment, use a tire that you are planning to throw away.

Place tires.
Place at least 2 tires under the tire which the front passenger airbag is tied to.
Place at least 2 tires over the tire which the front passenger airbag is tied to. The top tire should have a disc wheel installed.
- NOTICE:

Tie the tires together with 2 wire harnesses.
- CAUTION:
- Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.

Install SST.
Connect SST connector.
- SST
- 09082-00700
- NOTICE:
- To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.
Deploy the airbag.
Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.
Check that no one is within a 10 m (32.8 ft.) radius of the tire which the front passenger airbag is tied to.
Press SST activation switch to deploy the airbag.
- CAUTION:
- When deploying the airbag, make sure that no one is near the tire.
- HINT:
- The airbag is deployed as the LED of SST activation switch comes on.

Dispose of the front passenger airbag assembly.
- CAUTION:
Remove the front passenger airbag from the tire.
Place the front passenger airbag in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.