Entry Lock And Unlock Switch (For Rear) - Removal

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - THEFT DETERRENT / KEYLESS ENTRY

ENTRY LOCK AND UNLOCK SWITCH (for Rear) - REMOVAL

  • HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  • NOTICE:
  • When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
2. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a moulding remover, detach the 7 claws.

Disconnect the connector and remove the armrest base panel.

3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

  • HINT:
  • Tape the screwdriver tip before use.
Text in Illustration
*1Protective Tape
4. REMOVE ASSIST GRIP COVER LH
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.

5. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Detach the claw.

Remove the courtesy light and then disconnect the connector.

6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 3 screws.

Remove the 9 clips.

Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

  • HINT:
  • Make sure that the pin labeled A in the illustration is detached from the door panel.

Disconnect the connector and remove the rear door trim board sub-assembly LH.

Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the 2 cables from the rear door inside handle sub-assembly LH.

7. REMOVE REAR DOOR SERVICE HOLE COVER LH
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a clip remover, detach the 6 clamps.

Remove the bolt and disconnect the 2 connectors.

Remove the rear door service hole cover LH.

  • HINT:
  • Remove the remaining tape on the door.
8. REMOVE REAR DOOR LOCK ASSEMBLY LH
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a T30 ''TORX'' socket, remove the 3 screws and door lock.

  • NOTICE:
  • Be careful when removing the screws as the door lock may fall and become damaged.
9. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a T30 ''TORX'' socket, loosen the screw.

Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Detach the claw and remove the rear door outside handle cover LH.

10. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a T30 "TORX" wrench, loosen the screw.

Disconnect the connector.

Entry Lock And Unlock Switch (For Rear) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.