Entry Lock And Unlock Switch (For Front) - Removal

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - THEFT DETERRENT / KEYLESS ENTRY

ENTRY LOCK AND UNLOCK SWITCH (for Front) - REMOVAL

  • HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  • CAUTION:
  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  • NOTICE:
  • When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
2. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH LH
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Detach the clip and claw, and remove the front door lower frame bracket garnish LH.

3. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a moulding remover, detach the 5 claws.

Disconnect the connector and remove the armrest base panel.

4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a screwdriver, detach the 4 claws and remove the front door inside handle bezel LH.

  • HINT:
  • Tape the screwdriver tip before use.
Text in Illustration
*1Protective Tape
5. REMOVE DOOR ASSIST GRIP COVER LH
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.

6. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Detach the claw.

Remove the courtesy light and then disconnect the connector.

7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 3 screws.

Remove the 13 clips.

Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

  • HINT:
  • Make sure that the pin labeled A in the illustration is detached from the door panel.

Disconnect the connector.

Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the 2 cables from the front door inside handle sub-assembly LH.

8. REMOVE FRONT DOOR SERVICE HOLE COVER LH
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a clip remover, detach the 9 clamps.

Remove the bolt and disconnect the 2 connectors.

Remove the front door service hole cover LH.

  • HINT:
  • Remove the remaining tape on the door.
9. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the hole plug.

Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock cylinder installed.

Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Detach the 2 claws and remove the front door outside handle cover LH.

10. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH
Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the connector.

Using a T30 "TORX" wrench, loosen the screw.

Entry Lock And Unlock Switch (For Front) - Removal. THEFT DETERRENT / KEYLESS ENTRY. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

  • NOTICE:
  • If the release plate is not pulled and held when removing the handle, the release plate will interfere with the handle and become damaged.