Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - WIPER / WASHER
WIPER AND WASHER SYSTEM (w/ Rain Sensor) - DATA LIST / ACTIVE TEST
READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the "Data List".
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
F Wiper LO Switch | Front wiper LO switch / ON or OFF | ON: Front wiper switch in LO position OFF: Front wiper switch not in LO position | - |
F Wiper HI Switch | Front wiper HI switch / ON or OFF | ON: Front wiper switch in HI position OFF: Front wiper switch not in HI position | - |
F Wiper AUTO Switch | Front wiper AUTO switch / ON or OFF | ON: Front wiper switch in AUTO position OFF: Front wiper switch not in AUTO position | - |
F Wiper MIST Switch | Front wiper MIST switch / ON or OFF | ON: Front wiper switch in MIST position OFF: Front wiper switch not in MIST position | - |
F Washer Switch | Front washer switch / ON or OFF | ON: Front washer switch on OFF: Front washer switch off | - |
IG Switch SIG | Engine switch signal / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | "OFF" is also displayed for this item when the engine switch is on (ACC). |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
Rain Sensor Cold | Rain sensor cold / COLD or OK | COLD: Rain sensor is low temp OK: Rain sensor is normal | - |
Rain Sensor Hot | Rain sensor cold / HOT or OK | HOT: Rain sensor is high temp OK: Rain sensor is normal | - |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
Washer Level Switch | Washer fluid level warning switch / ON or OFF | ON: Washer jar and pump are empty OFF: Washer jar and pump are full | - |
IG Switch SIG | Engine switch signal / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | "OFF" is also displayed for this item when the engine switch is on (ACC). |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
Stop Light Switch | Stop light switch signal / ON or OFF | ON: Stop light switch on OFF: Stop light switch off | - |
PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- NOTICE:
- When a Body No. 5 (windshield wiper ECU) related front wiper switch is on, Active Test items related to the front wiper switch are prohibited (double operation prohibition). Check that the front wiper switches are off before performing Active Tests.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Active Test.
According to the display on the intelligent tester. perform the "Active Test".
Tester Display | Test Part | Control Range | Diagnostic Note |
Wiper Mot (HI) | Wiper motor HI operation | ON / OFF | - |
Wiper Mot (LO) | Wiper motor LO operation | ON / OFF | - |
Tester Display | Test Part | Control Range | Diagnostic Note |
Front Washer Nozzle Heater | Washer nozzle heater operation | ON / OFF | - |
Tester Display | Test Part | Control Range | Diagnostic Note |
Head Light Cleaner | Headlight low beam signal | ON / OFF | - |