Tail Gate Closer System - Tail Gate Does Not Open With Back Door Remote Control

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - DOOR / HATCH

WIRING DIAGRAM

INSPECTION PROCEDURE

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TAIL GATE PANEL OPEN)

READ VALUE USING INTELLIGENT TESTER (HANDLE SWITCH OF TAIL GATE PANEL)

INSPECT LOWER TAIL GATE LOCK ASSEMBLY

CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY - NO. 2 MAIN BODY ECU)

INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY

CHECK HARNESS AND CONNECTOR (BACK DOOR REMOTE CONTROL ASSEMBLY - NO. 2 MAIN BODY ECU AND BODY GROUND)

TAIL GATE CLOSER SYSTEM - Tail Gate does not Open with Back Door Remote Control

WIRING DIAGRAM

Tail Gate Closer System - Tail Gate Does Not Open With Back Door Remote Control. DOOR / HATCH. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TAIL GATE PANEL OPEN)

Select the Active Test, use the intelligent tester to generate a control command, and check that the lower tail gate lock operates ().

Body No. 4
Tester DisplayTest PartControl RangeDiagnostic Note
Tail Gate Panel OpenLower tail gate lockON / OFF The back door must be open.
  • OK:
  • Lower tail gate lock operates normally.
NG
Go to step 3
OK
2.READ VALUE USING INTELLIGENT TESTER (HANDLE SWITCH OF TAIL GATE PANEL)

Check the Data List for proper functioning of the back door remote control ().

Body No. 4
Tester DisplayMeasurement Item/RangeNormal ConditionDiagnostic Note
Handle Switch of tail gate panel Back door remote control signal / ON or OFF ON: Back door remote control pulled
OFF: Back door remote control free		-
  • OK:
  • The display is as specified in the normal condition.
NG
Go to step 5
OK
REPLACE NO. 2 MAIN BODY ECU ()
3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY

for LH:


Remove the lower tail gate lock assembly LH ().

Inspect the lower tail gate lock assembly LH ().

for RH:


Remove the lower tail gate lock assembly RH ().

Inspect the lower tail gate lock assembly RH ().

Result
ResultProceed to
OKA
NG (for LH)B
NG (for RH)C
B
REPLACE LOWER TAIL GATE LOCK ASSEMBLY LH ()
C
REPLACE LOWER TAIL GATE LOCK ASSEMBLY RH ()
A
4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY - NO. 2 MAIN BODY ECU)

for LH:


Disconnect the h5 lower tail gate lock assembly LH connector.

Disconnect the L51 No. 2 main body ECU connector.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    h5-5 (ACT+) - L51-3 (DC+)AlwaysBelow 1 Ω
    h5-6 (ACT-) - L51-8 (DC-)AlwaysBelow 1 Ω
    h5-5 (ACT+) - Body groundAlways10 kΩ or higher
    h5-6 (ACT-) - Body groundAlways10 kΩ or higher

for RH:


Disconnect the h4 lower tail gate lock assembly RH connector.

Disconnect the L51 No. 2 main body ECU connector.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    h4-5 (ACT+) - L51-2 (DC+)AlwaysBelow 1 Ω
    h4-6 (ACT-) - L51-1 (DC-)AlwaysBelow 1 Ω
    h4-5 (ACT+) - Body groundAlways10 kΩ or higher
    h4-6 (ACT-) - Body groundAlways10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE NO. 2 MAIN BODY ECU ()
5.INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY

Remove the back door remote control assembly ().

Inspect the back door remote control assembly ().

NG
REPLACE BACK DOOR REMOTE CONTROL ASSEMBLY ()
OK
6.CHECK HARNESS AND CONNECTOR (BACK DOOR REMOTE CONTROL ASSEMBLY - NO. 2 MAIN BODY ECU AND BODY GROUND)

Disconnect the h3 back door remote control assembly connector.

Disconnect the L50 No. 2 main body ECU connector.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    h3-2 - L50-19 (BDSU)AlwaysBelow 1 Ω
    h3-1 - Body groundAlwaysBelow 1 Ω
    h3-2 - Body groundAlways10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE NO. 2 MAIN BODY ECU ()