Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - EXTERIOR PANELS / TRIM

ROOF DRIP SIDE FINISH MOULDING - REMOVAL

  • HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
When replacing a clip, heat the vehicle body and clip using a heat light.
  • Standard Heating Temperature:
  • ItemTemperature
    Vehicle Body40 to 60°C (104 to 140°F)
    Clip20 to 30°C (68 to 86°F)
  • NOTICE:
  • Do not heat the vehicle body and clip excessively.
1. REMOVE ROOF CARRIER ASSEMBLY LH (w/ Roof Carrier)

Remove the roof carrier assembly LH ().

2. REMOVE ROOF RACK ASSEMBLY (w/ Roof Rack)

Remove the roof rack assembly ().

3. REMOVE ROOF DRIP SIDE FINISH MOULDING JOINT COVER LH
Roof Drip Side Finish Moulding - Removal. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Put protective tape around the cover.

w/o Roof Carrier:


Detach the claw and clip and remove the 4 covers.

w/ Roof Carrier:


Detach the claw and clip and remove the cover.

4. REMOVE ROOF DRIP SIDE FINISH MOULDING LH
Roof Drip Side Finish Moulding - Removal. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200
  • HINT:
  • Use the same procedure to remove the moulding on the other side.

Put protective tape around the moulding.

Remove the moulding.

5. REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING LH
Roof Drip Side Finish Moulding - Removal. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200
  • HINT:
  • Use the same procedure to remove the moulding on the other side.

Put protective tape around the moulding.

Remove the moulding.

6. REMOVE REAR ROOF DRIP SIDE FINISH MOULDING LH
Roof Drip Side Finish Moulding - Removal. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Put protective tape around the moulding.

Using a moulding remover, detach the clip and remove the moulding.

  • NOTICE:
When removing the rear roof drip side finish moulding, be careful not to damage the No. 1 roof drip side finish moulding clip.
If the No. 1 roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.
7. REMOVE NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP
Roof Drip Side Finish Moulding - Removal. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200
  • HINT:
  • Perform the following procedures if replacing a No. 1 roof drip side finish moulding clip.

Using a heat light, heat the clip and vehicle body.

  • NOTICE:
  • Do not heat the clip and vehicle body excessively.

Remove the clip.

8. REMOVE ROOF RACK BRACKET
Roof Drip Side Finish Moulding - Removal. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

w/o Roof Carrier:


Remove the 8 bolts and 4 brackets.

w/ Roof Carrier:


Remove the 2 bolts and bracket.

9. REMOVE NO. 2 ROOF DRIP SIDE FINISH MOULDING RETAINER (w/ Roof Carrier)
Roof Drip Side Finish Moulding - Removal. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 2 bolts and retainer.

EXTERIOR PANELS / TRIM
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
ROOF DRIP SIDE FINISH MOULDING