Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - EXTERIOR PANELS / TRIM

REAR BUMPER (for Standard) - REASSEMBLY

1. INSTALL REAR NO. 2 BUMPER SIDE BRACKET (w/ Tire Carrier)

Attach the 3 claws and 2 clips to install the rear No. 2 bumper side bracket and rear No. 3 bumper side bracket.

Install the 2 screws.

2. INSTALL REFLEX REFLECTOR ASSEMBLY LH (w/o Rear Fog Light)

Attach the claw to install the reflex reflector assembly LH.

Install the 2 nuts.

3. INSTALL REFLEX REFLECTOR ASSEMBLY RH (w/o Rear Fog Light)
  • HINT:
  • Use the same procedure described for the LH side.
4. INSTALL REAR FOG LIGHT ASSEMBLY LH (w/ Rear Fog Light)
Rear Bumper (For Standard) - Reassembly. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the claw.

Connector the connectors.

Install the fog light with the 2 nuts.

5. INSTALL REAR FOG LIGHT ASSEMBLY RH (w/ Rear Fog Light)
  • HINT:
  • Use the same procedure described for the LH side.
6. INSTALL REAR BUMPER ENERGY ABSORBER

Attach the 8 claws to install the rear bumper energy absorber.

7. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
  • HINT:
  • Use the same procedure to install the No. 1 ultrasonic sensor retainer on the other side.
Rear Bumper (For Standard) - Reassembly. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Align the keyhole and protrusion as shown in the illustration.

Text in Illustration
*aProtrusion
*bKeyhole
  • NOTICE:
Do not damage the bumper with the protrusion when installing the No. 1 ultrasonic sensor retainer.
Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the rear bumper.
  • HINT:
  • The illustration shows the No. 1 ultrasonic sensor retainer for the RH corner. The vertical orientation of the No. 1 ultrasonic sensor retainers for the LH corner is opposite that of the image shown in the illustration.

Attach the 2 claws to install the No. 1 ultrasonic sensor retainer.

8. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
  • HINT:
  • Use the same procedure to install the No. 2 ultrasonic sensor retainer on the other side.
Rear Bumper (For Standard) - Reassembly. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Align the keyhole and protrusion as shown in the illustration.

Text in Illustration
*aProtrusion
*bKeyhole
  • NOTICE:
Do not damage the bumper with the protrusion when installing the No. 2 ultrasonic sensor retainer.
Securely install the No. 2 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the rear bumper.

Attach the 2 claws to install the No. 2 ultrasonic sensor retainer.

9. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
  • HINT:
  • Use the same procedure for all No. 1 ultrasonic sensors.

Attach the 2 claws to install the No. 1 ultrasonic sensor.

  • NOTICE:
  • Push the ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.
10. INSTALL NO. 2 FRAME WIRE

w/ TOYOTA Parking Assist-sensor System, w/o Rear Fog Light:


Install the No. 2 frame wire.

Attach the 12 clamps to install the No. 2 frame wire.

Connect the 4 connectors.

w/ TOYOTA Parking Assist-sensor System, w/ Rear Fog Light:


Install the No. 2 frame wire.

Attach the 14 clamps to install the No. 2 frame wire.

Connect the 6 connectors.

w/o TOYOTA Parking Assist-sensor System, w/ Rear Fog Light:


Install the No. 2 frame wire.

Attach the 13 clamps to install the No. 2 frame wire.

Connect the 2 connectors.

EXTERIOR PANELS / TRIM
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
REAR BUMPER for Standard