Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - EXTERIOR PANELS / TRIM

REAR BUMPER (for Standard) - INSTALLATION

  • HINT:
  • A bolt without a torque specification is shown in the standard bolt chart ().
1. INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

Install the No. 2 luggage compartment side cover protector with 2 new grommets.

Install the 2 screws.

2. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR
  • HINT:
  • Use the same procedure described for the LH side.
3. INSTALL REAR BUMPER ARM BRACKET LH

Install the rear bumper arm bracket LH with the 2 bolts.

Connect the connector.

4. INSTALL REAR BUMPER ARM BRACKET

Install the rear bumper arm bracket with the bolt.

  • HINT:
  • Use the same procedure to install the rear bumper arm bracket on the other side.
5. INSTALL REAR NO. 2 BUMPER REINFORCEMENT

Install the rear No. 2 bumper reinforcement with the 2 bolts.

6. INSTALL REAR BUMPER SIDE SUPPORT LH

Attach the 6 claws to install the rear bumper side support LH.

Install the 3 screws.

7. INSTALL REAR BUMPER SIDE SUPPORT RH
  • HINT:
  • Use the same procedure described for the LH side.
8. INSTALL REAR UPPER BUMPER RETAINER LH

Attach the 2 clips to install the rear upper bumper retainer LH.

9. INSTALL REAR UPPER BUMPER RETAINER RH
  • HINT:
  • Use the same procedure described for the LH side.
10. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

Connect the connector.

Attach the 2 clips to install the rear combination light assembly LH.

Install the 2 bolts.

Attach the 6 claws and install the 2 covers.

11. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH
  • HINT:
  • Use the same procedure described for the LH side.
12. INSTALL REAR BUMPER COVER
  • HINT:
  • For the rear bumper cover with tire carrier, use the procedures described below.

w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:


Connect the No. 2 frame wire connector.

Attach the 14 claws to install the rear bumper cover.

Install the 7 bolts, 6 screws and 2 clips.

Open the tail gate and install the 4 clips.

Close the tail gate.

13. INSTALL REAR NO. 1 BUMPER PLATE

Attach the 20 claws to install the rear No. 1 bumper plate.

14. INSTALL REAR QUARTER PANEL MUDGUARD LH
Rear Bumper (For Standard) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the mudguard with the clip.

Using a T30 "TORX" socket, install the 6 screws.

15. INSTALL REAR QUARTER PANEL MUDGUARD RH
Rear Bumper (For Standard) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the mudguard with the clip.

Using a T30 "TORX" socket, install the 7 screws.

16. INSTALL SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)

Clean the threaded surfaces on the vehicle body with a non-residue solvent.

Apply adhesive to the threads of the 6 bolts.

  • Adhesive:
  • Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

Install the spare wheel carrier with the 6 bolts.

  • Torque:
  • 28.4 N*m{ 290 kgf*cm, 21 ft.*lbf}

Rear Bumper (For Standard) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the spare tire.

  • Torque:
  • 90 N*m{ 918 kgf*cm, 66 ft.*lbf}
17. INSTALL SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)
Rear Bumper (For Standard) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the clip to install the cover.

Install the 2 nuts.

18. INSTALL SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)
Rear Bumper (For Standard) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Attach the 2 claws to install the bracket.

EXTERIOR PANELS / TRIM
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
REAR BUMPER for Standard