Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - EXTERIOR PANELS / TRIM

REAR BUMPER (for Double Swing Out Type) - INSTALLATION

  • HINT:
  • A bolt without a torque specification is shown in the standard bolt chart ().
1. INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

Install the No. 2 luggage compartment side cover protector with 2 new grommets.

Install the 2 screws.

2. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR
  • HINT:
  • Use the same procedure described for the No. 2 luggage compartment side cover protector.
3. INSTALL REAR BUMPER ARM BRACKET LH

Install the rear bumper arm bracket with the 2 bolts and nut.

Attach the clamp.

4. INSTALL REAR BUMPER ARM BRACKET
  • HINT:
  • Use the same procedure for both rear bumper arm brackets.

Install the rear bumper arm bracket with the bolt.

5. INSTALL REAR BUMPER NO. 2 REINFORCEMENT

Install the rear bumper No. 2 reinforcement with the 2 bolts.

6. INSTALL REAR BUMPER SIDE SUPPORT LH

Attach the 6 claws to install the rear bumper side support.

Install the 3 screws.

7. INSTALL REAR BUMPER SIDE SUPPORT RH
  • HINT:
  • Use the same procedure described for the LH side.
8. INSTALL REAR BUMPER UPPER RETAINER LH

Attach the 2 clips to install the rear bumper upper retainer.

9. INSTALL REAR BUMPER UPPER RETAINER RH
  • HINT:
  • Use the same procedure described for the LH side.
10. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH
Rear Bumper (For Double Swing Out Type) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Connect the connector.

Text in Illustration
*1Protective tape

Attach the 3 clips, 2 guides and 2 claws to install the rear combination light assembly LH.

  • NOTICE:
  • Attach the bolt installation bracket form outside the body while being careful not to bend it.

Install the 2 bolts.

11. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH
  • HINT:
  • Use the same procedure described for the LH side.
12. INSTALL REAR BUMPER COVER

Open the back doors one notch.

Attach the 14 claws to install the rear bumper cover.

Connect the No. 2 frame wire connector.

Install the 5 bolts and 2 clips.

Install the 2 bolts, 2 clips and 6 screws.

13. INSTALL REAR BUMPER NO. 1 PLATE

Attach the 20 claws to install the rear bumper No. 1 plate.

14. INSTALL REAR QUARTER PANEL MUDGUARD LH
Rear Bumper (For Double Swing Out Type) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the mudguard with the clip.

Using a T30 "TORX" socket, install the 6 screws.

15. INSTALL REAR QUARTER PANEL MUDGUARD RH
Rear Bumper (For Double Swing Out Type) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the mudguard with the clip.

Using a T30 "TORX" socket, install the 7 screws.

16. INSTALL PINTLE HOOK ASSEMBLY (w/ Pintle Hook)

Install the pintle hook assembly and pintle hook bracket with the 2 bolts, 2 eyelet pintle hooks and 4 nuts.

  • Torque:
  • for nut:
  • 65 N*m{ 663 kgf*cm, 48 ft.*lbf}

For vehicles with a spare installed to the underbody, install the spare tire.

17. INSTALL SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)

Clean the threaded surfaces on the vehicle body with a non-residue solvent.

Apply adhesive to the threads of bolt A and B.

  • Adhesive:
  • Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Rear Bumper (For Double Swing Out Type) - Installation. EXTERIOR PANELS / TRIM. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Install the spare wheel carrier with the 9 bolts.

  • Torque:
  • Bolt A:
  • 29 N*m{ 196 kgf*cm, 21 ft.*lbf}
  • Bolt B:
  • 15 N*m{ 148 kgf*cm, 11 ft.*lbf}
Text in Illustration
*1Bolt A
*2Bolt B

Install the spare tire with the 3 bolts.

  • Torque:
  • 90 N*m{ 918 kgf*cm, 66 ft.*lbf}
18. INSTALL SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

Attach the clip to install the spare wheel cover.

Install the 2 nuts.

19. INSTALL SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

Attach the 2 claws to install the spare wheel carrier hinge bracket.

EXTERIOR PANELS / TRIM
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
REAR BUMPER for Double Swing Out Type