Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - WINDOW / GLASS
POWER WINDOW REGULATOR MOTOR (for Rear Door) - REMOVAL
- HINT:
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work ().
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
| 3. REMOVE REAR DOOR INSIDE HANDLE BEZEL |
Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.
- HINT:
- Tape the screwdriver tip before use.
| *1 | Protective Tape |
| 4. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY |
Using a moulding remover, detach the 7 claws.
Disconnect the connector and remove the armrest base panel.
| 5. REMOVE ASSIST GRIP COVER |
Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.
| 6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
Remove the 3 screws.
Remove the 9 clips.
Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.
- HINT:
- Make sure that the pin labeled A in the illustration is detached from the door panel.
Disconnect the connector and remove the rear door trim board sub-assembly LH.
Disconnect the 2 cables from the rear door inside handle sub-assembly LH.
| 7. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP |
Install the rear inner door glass weatherstrip LH to the door panel.
| 8. REMOVE REAR SPEAKER SET (w/ Rear Speaker) |
Disconnect the speaker connector.
Remove the 3 screws.
Detach the claw and remove the speaker.
- NOTICE:
- Do not touch the cone part of the speaker.
| 9. REMOVE REAR DOOR SERVICE HOLE COVER |
Using a clip remover, detach the 6 clamps.
Remove the bolt and disconnect the 2 connectors.
Remove the rear door service hole cover LH.
- HINT:
- Remove the remaining tape on the door.
| 10. REMOVE REAR DOOR GLASS RUN |
Remove the rear door glass run LH from the window frame.
| 11. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY |
Remove the 2 bolts.
Remove the screw and rear door rear lower window frame sub-assembly LH.
| 12. REMOVE REAR DOOR QUARTER WINDOW GLASS |
Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.
| 13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.
- NOTICE:
- Do not damage the door glass.
| 14. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Loosen the temporary bolt.
- NOTICE:
- Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and cause damage.
| *1 | Temporary Bolt |
Remove the 3 bolts and rear door window regulator sub-assembly LH.
- NOTICE:
- Be careful when removing the bolts as the motor may fall and become damaged.
Remove the temporary bolt from the rear door window regulator sub-assembly LH.
| 15. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY |
Using a T25 "TORX" driver, remove the 3 screws and motor.
- NOTICE:
- Be careful when removing the screws as the motor may fall and become damaged.
| *A | for Models with Jam Protection Function on 4 Windows |
| *B | for Models with Jam Protection Function on Driver Door Window Only |