Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - WINDOW / GLASS

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK LIN COMMUNICATION SYSTEM

CHECK FOR DTC (B2312)

READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR LH)

CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - BODY GROUND)

CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR LH - BATTERY AND BODY GROUND)

CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)

INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows) - Rear Power Window LH does not Operate with Rear Power Window Switch LH

DESCRIPTION

If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, power window rear regulator motor LH, harness or connector.

WIRING DIAGRAM

Power Window Control System (For Models With Jam Protection Function On 4 Windows) - Rear Power Window Lh Does Not Operate With Rear Power Window Switch Lh. WINDOW / GLASS. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

INSPECTION PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM

Check for LIN communication system DTCs related to the power window control system ().

  • OK:
  • LIN communication system DTCs are not output.
NG
GO TO LIN COMMUNICATION SYSTEM ()
OK
2.CHECK FOR DTC (B2312)

Check if DTC B2312 is output ().

  • OK:
  • DTC B2312 is not output.
NG
GO TO DTC B2312 ()
OK
3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR LH)

Use the Data List to check if the power window regulator motor is functioning properly ().

RL-Door Motor
Tester DisplayMeasurement Item/RangeNormal ConditionDiagnostic Note
RL Door P/W Up SW Rear power window LH manual up signal / ON or OFF ON: Rear power window LH manual up switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Down SW Rear power window LH manual down signal / ON or OFF ON: Rear power window LH manual down switch operated
OFF: Rear power window LH switch not operated
-
  • OK:
  • The display changes according to operation of the rear power window switch LH.
NG
Go to step 4
OK
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH ()
4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - BODY GROUND)
Power Window Control System (For Models With Jam Protection Function On 4 Windows) - Rear Power Window Lh Does Not Operate With Rear Power Window Switch Lh. WINDOW / GLASS. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

Disconnect the J10 switch connector.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    J10-1 (GND) - Body groundAlwaysBelow 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR LH - BATTERY AND BODY GROUND)
Power Window Control System (For Models With Jam Protection Function On 4 Windows) - Rear Power Window Lh Does Not Operate With Rear Power Window Switch Lh. WINDOW / GLASS. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

Disconnect the J11 motor connector.

Measure the voltage and resistance according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionConditionSpecified Condition
    J11-2 (B) - Body groundAlways11 to 14 V
  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    J11-1 (GND) - Body groundAlwaysBelow 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
6.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)
Power Window Control System (For Models With Jam Protection Function On 4 Windows) - Rear Power Window Lh Does Not Operate With Rear Power Window Switch Lh. WINDOW / GLASS. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

Disconnect the J10 switch connector.

Disconnect the J11 motor connector.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    J10-6 (UP) - J11-10 (UP)AlwaysBelow 1 Ω
    J10-7 (DOWN) - J11-7 (DOWN)AlwaysBelow 1 Ω
    J10-8 (AUTO) - J11-4 (AUTO)AlwaysBelow 1 Ω
    J10-6 (UP) or J11-10 (UP) - Body groundAlways10 kΩ or higher
    J10-7 (DOWN) or J11-7 (DOWN) - Body groundAlways10 kΩ or higher
    J10-8 (AUTO) or J11-4 (AUTO) - Body groundAlways10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
7.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
Power Window Control System (For Models With Jam Protection Function On 4 Windows) - Rear Power Window Lh Does Not Operate With Rear Power Window Switch Lh. WINDOW / GLASS. Land Cruiser URJ200  URJ202 GRJ200 VDJ200

Remove the rear power window regulator switch ().

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionSwitch ConditionSpecified Condition
    J10-6 (UP) - J10-1 (GND)Manual up operationBelow 1 Ω
    J10-7 (DOWN) - J10-1 (GND)Manual down operationBelow 1 Ω
NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH ()
OK
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH ()