Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - MIRROR EXT
OUTER REAR VIEW MIRROR - DISASSEMBLY
- HINT:
| 1. REMOVE OUTER MIRROR LH |
Push the upper part of the mirror surface and tilt it.
Using a moulding remover, detach the 4 claws and separate the outer mirror LH from the mirror body.
- HINT:
- Apply protective tape to the outer rear mirror LH to prevent it from being damaged.
w/ EC Mirror:
Disconnect the connector and remove the outer mirror LH.
w/ Mirror Heater:
Disconnect the 2 connectors and remove the outer mirror LH.
| 2. REMOVE OUTER MIRROR COVER |
- HINT:
- Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.
Using 2 screwdrivers, detach the 2 claws.
- HINT:
- Tape the screwdriver tip before use.
| *1 | Protective Tape |
Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.
- NOTICE:
- Be careful not to break the ribs.
- HINT:
- Tape the screwdriver tip before use.
| *1 | Protective Tape | *2 | Rib |
| *a | Inner Side of Outer Mirror Cover | - | - |
Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.
- HINT:
- Tape the moulding remover before use.
| *1 | Protective Tape |
Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.
- NOTICE:
- Do not insert the moulding remover more than 4 mm (0.157 in.).
- Standard:
Area Specified Condition a 4mm
Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.
- NOTICE:
| *1 | Protective Tape |
- Standard:
Area Specified Condition a 40mm b 4mm
Remove the moulding remover B.
Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.
| *1 | Protective Tape |
| *a | Lower Side |
Insert a moulding remover B between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.
Using a screwdriver, detach the claw.
| *1 | Protective Tape |
Detach the 2 claws and remove the outer mirror cover.
- NOTICE:
- When removing the cover, be careful not to damage the side turn signal light assembly or cover.
| 3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH |
Remove the 3 screws and light.
Disconnect the connector.
| 4. REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System) |
Remove the gasket
Remove the tape.
Detach the 9 guides and remove the gasket.
- HINT:
- Slightly lower the gasket so that the television camera assembly can be removed.
Remove the lower mirror cover
Using a screwdriver with its tip wrapped in protective tape, disconnect the 4 claws and remove the lower mirror cover.
| *1 | Protective Tape |
Remove the base
Remove the wire harness.
Using "TORX" socket wrench T25, remove the 3 screws.
- NOTICE:
- Make sure to replace the "TORX" screws with new ones.
Disconnect the guide and remove the base.
Detach the connector from the wire clip.
Using a screwdriver, disconnect the connector.
- HINT:
- Tape the moulding remover before use.
| *1 | Protective Tape |
Remove the body
Remove the 5 screws and body.
Remove the body
Disconnect the 2 guides and remove the body.
- NOTICE:
- Be careful not to break the guide shown in the part of the illustration labeled A.
Remove the 3 screws and side television camera.