Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - LIGHTING EXT
LIGHTING SYSTEM - OPERATION CHECK
| CHECK ILLUMINATED ENTRY SYSTEM OPERATION |
The illuminated entry system controls the following lights:
Check the illuminated entry system with the ignition switch off.
Check that the lights turn on when unlocking any of the doors that are closed and locked with the ignition switch off. Then check that the lights fade out under the following conditions:
Check that the lights stay on for at least 15 seconds after opening any of the doors before fading out. Then check that the lights fade out 15 seconds after closing all the doors.
Check the illuminated entry system with the ignition switch to ACC or ON.
Check that the lights stay lit after turning the ignition switch off with all the doors closed and the ignition switch to ACC or ON. Then check that the lights fade out under the following conditions:
Check that the lights stay on for at least 15 seconds after opening any of the doors. Then check that the lights fade out 15 seconds after closing all the doors.
Check that the lights turn on when opening any of the doors and fade out when closing and locking all the doors or turning the ignition switch to ACC or ON.
| CHECK BATTERY SAVER OPERATION |
Basic function inspection
Check that the applicable lights are turned off approximately 20 minutes after the ignition switch is turned off with any door left open or ajar.
Interior light auto cut function inspection (w/ Dome Cut Relay)
Check that the applicable lights are turned off approximately 20 minutes after the ignition switch is turned off regardless of the open/close status of the doors or the position of the map light switch.
| CHECK LIGHT AUTO TURN OFF OPERATION |
Prepare the vehicle so that the ignition switch is ON and the driver door is closed.
Set the headlight dimmer switch assembly to TAIL, HEAD or AUTO to illuminate the lights.
Turn the ignition switch off and open the driver door. When the headlight dimmer switch is on AUTO, check that the headlights, fog lights, and taillights turn off. When the headlight dimmer switch is on head or tail, check that the headlights and front fog lights turn off.
| AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM OPERATION CHECK (w/ Static Headlight Auto Leveling) |
Check that the initialization (determination of the initial position) of the headlight leveling motor is performed when the ignition switch is turned to ON.
Check that the headlight beam level control system warning light in the combination meter assembly comes on for approximately 3 seconds when the ignition switch is turned to ON, and then turns off.
Check that the headlight moves when all of the following conditions are met: 1) the rear of the vehicle is moved up or down, 2) the engine is running, 3) the vehicle is stopped, and 4) the light control switch is in the head position.
- NOTICE:
- Make sure to change the vehicle height slowly.
| AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM OPERATION CHECK (w/ Dynamic Headlight Auto Leveling) |
Check that the initialization (determination of the initial position) of the headlight leveling motor is performed after the engine is started.
Check that the headlight beam level control system warning light in the combination meter comes on for approximately 3 seconds and then goes off when the ignition switch is turned to ON.
| INSPECT AUTOMATIC HIGH BEAM SYSTEM (w/ Automatic High Beam System) |
Check the operation of the inner rear view mirror indicator light.
Turn the ignition switch ON.
Check that the inner rear view mirror indicator light comes on.
Press the inner rear view mirror assembly AUTO switch once.
Check that the inner rear view mirror indicator light goes off.
Press the inner rear view mirror assembly AUTO switch once again.
Check that the inner rear view mirror indicator light comes on.
- HINT:
- If the inner rear view mirror indicator light flashes, turn the ignition switch off, and then turn the ignition switch ON. If the inner rear view mirror indicator light flashes continuously, replace the inner rear view mirror assembly.
Check the operation of the automatic high beam indicator light.
Turn the ignition switch ON.
Move the shift lever to any position except R.
Turn the light control switch to the AUTO position.
Cover the automatic light control sensor to turn the low beam headlights on.
Turn the dimmer switch to the high position.
Check that the automatic high beam indicator comes on.
Check the operation of the automatic high beam function.
At night, when driving the vehicle with the automatic high beam system in standby mode, check that the headlights are changed from the low beams to the high beams automatically after a short delay when all of the following conditions are met:
At night, when driving the vehicle with the high beams turned on by the automatic high beam system, check that the automatic high beam system turns off the high beams and returns to standby mode when any of the following conditions are met:
Using the following procedure, the automatic high beam operation can be checked without driving the vehicle.
Turn the ignition switch ON.
Using the intelligent tester, follow the instructions to switch to the "AFS" screen and select "Active Test".
Select "Automatic High Beam Operation" on the screen and forcibly operate the automatic high beam system.
Check that the inner rear view mirror indicator light flashes.
Check that the low beams change to the high beams when the surrounding area is dark enough.
Shine a flashlight, white LED or red LED on the camera built into the inner rear view mirror.
Check that the high beams change to the low beams.
- NOTICE:
- The high beams may not change to the low beams when the surrounding area is bright or due to on other lighting conditions. Therefore, this function check should not be used as the only method of determining if a malfunction is present (if parts need to be replaced).