Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - LIGHTING EXT
LIGHTING SYSTEM - DATA LIST / ACTIVE TEST
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ACC SW | Ignition switch / ACC or OFF | ON: Ignition switch ACC OFF: Ignition switch off | "ON" is also displayed for this item when the ignition switch is ON. |
| IG SW | Ignition switch / ON or OFF | ON: Ignition switch ON OFF: Ignition switch off | "OFF" is also displayed for this item when the ignition switch is ACC. |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| D Door Courtesy SW | Front door courtesy light switch LH signal / ON or OFF | ON: Front door courtesy light switch LH on OFF: Front door courtesy light switch LH off | - |
| P Door Courtesy SW | Front door courtesy light switch RH signal / ON or OFF | ON: Front door courtesy light switch RH on OFF: Front door courtesy light switch RH off | - |
| RR Door Courtesy SW | Rear door courtesy light switch RH signal / ON or OFF | ON: Rear door courtesy light switch RH on OFF: Rear door courtesy light switch RH off | - |
| RL Door Courtesy SW | Rear door courtesy light switch LH signal / ON or OFF | ON: Rear door courtesy light switch LH on OFF: Rear door courtesy light switch LH off | - |
| Back Door Courtesy SW | Back door courtesy light switch signal / ON or OFF | ON: Back door courtesy light switch on OFF: Back door courtesy light switch off | - |
| Dimmer SW | Dimmer switch signal / ON or OFF | ON: Dimmer switch high OFF: Dimmer switch except high | - |
| Passing Light SW | Passing light switch signal / ON or OFF | ON: Passing light switch on OFF: Passing light switch off | - |
| Front Fog Light SW*1 | Front fog light switch signal / ON or OFF | ON: Front fog light switch on OFF: Front fog light switch off | - |
| Auto Light SW*2 | Auto light switch signal / ON or OFF | ON: Auto light switch on OFF: Auto light switch off | - |
| Head Light SW (Head) | Headlight switch signal / ON or OFF | ON: Light control switch head OFF: Light control switch except head | - |
| Head Light SW (Tail) | Taillight switch signal / ON or OFF | ON: Light control switch tail OFF: Light control switch neither tail nor head | - |
| Illumination Rate lnfo | Illumination rate / min.: 0, max.: 99.99 | Actual illumination rate displayed | - |
| I/L ON W/Door Key Unlock | Interior light ON with unlock / ON or OFF | Customize setting displayed. | - |
| Lighting Time | Lighting Time / 7.5s or 15s or 30s | Customize setting displayed. | - |
| I/L when ACC OFF | I/L ON/ACC OFF Light the I/L when ACC OFF / ON or OFF | Customize setting displayed. | - |
| Light Control | Function which controls interior lights / ON or OFF | Customize setting displayed. | - |
| Sensitivity | Turn on luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2 | Customize setting displayed. | - |
| Disp Ex ON Sen | Display extinction luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2 | Customize setting displayed. | - |
| Disp Ex OFF Sen | Display extinction release luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2 | Customize setting displayed. | - |
*1: w/ Front Fog Light
*2: w/ Automatic Light Control System
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Headlight Low Beam State | Low beam headlight state / ON or OFF | ON: Low beam headlights on OFF: Low beam headlights off | - |
| +B | Ignition power supply voltage value / 0 to 19.75 V | 11 to 14 V | - |
| Height Sens Pw Supply Val | Rear height control sensor power supply value / 0 to 5 V | Approximately 5 V | - |
| Rr Height Sens Signal Val | Rear height control sensor signal value / 0 to 5 V | Approximately 2.5 V (When vehicle level) | The value changes according to the vehicle height. |
| Vehicle Speed | Vehicle speed / 0 to 327.67 km/h | Actual vehicle speed | - |
| Rear Height Adjust Valid Flag | Result of rear vehicle height calibration / Valid or Inval | Valid: Rear vehicle height calibration completed Inval: Rear vehicle height calibration not completed | - |
| Init Writing Count | Number of times initialization performed / 0 to 255 | Current condition displayed | - |
| Sensor Initialization Hist | Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied | Current condition displayed | - |
| Number Of Trouble Codes | Number of trouble codes / 0 to 255 | Condition can be displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Headlight Low Beam State | Low beam headlight state / ON or OFF | ON: Low beam headlights on OFF: Low beam headlights off | - |
| Headlight High Beam State | High beam headlight state / ON or OFF | ON: High beam headlights on OFF: High beam headlights off | - |
| Engine | Engine condition / Run or Stop | Run: Engine running Stop: Engine stopped | - |
| +B | Ignition power supply voltage value / 0 to 19.75 V | 11 to 14 V | - |
| Height Sens Pw Supply Val | Height control sensor power supply value / 0 to 6.25 V | 4.7 to 5.2 V | - |
| Fr Height Sens Signal Val* | Front height control sensor signal value / 0 to 5 V | Approximately 2.5 V (When vehicle level) | The value changes according to the vehicle height. |
| Rr Height Sens Signal Val | Rear height control sensor signal value / 0 to 5 V | Approximately 2.5 V (When vehicle level) | The value changes according to the vehicle height. |
| FR Wheel Speed | Front right wheel speed / 0 to 327.67 km/h | Condition can be displayed | - |
| FL Wheel Speed | Front left wheel speed / 0 to 327.67 km/h | Condition can be displayed | - |
| Vehicle Speed | Vehicle speed / 0 to 327.67 km/h | Condition can be displayed | - |
| Rear Height Adjust Valid Flag | Rear height adjustment range / Valid or Inval | Condition can be displayed | - |
| Init Writing Count | Number of times for initialization / 0 to 255 | Condition can be displayed | - |
| Sensor Initialization Hist | Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied | Condition can be displayed | - |
| Number Of Trouble Codes | Number of trouble codes / 0 to 255 | Condition can be displayed | - |
*: w/ Active Height Control Suspension
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the Ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Hazard | Hazard warning signal | ON/OFF | - |
| Illuminated Entry System | Illumination light | ON/OFF | - |
| Indicator for Lighting | Illumination of switch indicator operation | ON/OFF | - |
| Taillight Relay | Taillight | ON/OFF | - |
| Headlight Relay | Headlight | ON/OFF | - |
| Head Light Hi | Headlight (Hi) | ON/OFF | - |
| Front Fog Light Relay*1 | Front fog light | ON/OFF | - |
| Rear Fog Light Relay*2 | Rear fog light | ON/OFF | - |
| Relay for Interior Light Auto Cut Function*3 | DOME CUT relay | ON/OFF | Perform the Active test of the DOME CUT relay when the ignition switch is off |
| Dimmer Signal | Illumination dimming operation | ON/OFF | - |
*1: w/ Front Fog Light
*2: w/ Rear Fog Light
*3: w/ Dome Cut Relay
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Rear Step Light | Step light operation | OFF/ON | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Drive The Leveling Motor UP* | Headlight leveling motor upward operation | ON/OFF | ON: Move up OFF: Stop |
| Drive The Leveling Motor DOWN* | Headlight leveling motor downward operation | ON/OFF | ON: Move down OFF: Stop |
*: Perform the Active Test with the engine running and vehicle stopped.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Drive The Leveling Motor UP1 | Headlight leveling motor upward operation | ON/OFF | ON: Move up OFF: Stop |
| Drive The Leveling Motor DOWN*1 | Headlight leveling motor downward operation | ON/OFF | ON: Move down OFF: Stop |
| AFS OFF Indicator | Headlight beam level control system warning light | ON/OFF | - |
| Automatic High Beam Operation*2 | Automatic high beam system operation | ON/OFF | - |
*1: Perform the Active Test with the engine running and vehicle stopped.
*2: w/ Automatic High Beam System