Dtc B2343 Position Initialization Incomplete
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
CHECK FOR DTC
CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)
INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
DTC B2343 Position Initialization Incomplete
DESCRIPTION
This DTC is output when the sliding roof drive gear (sliding roof ECU) has not been initialized.
| DTC Code | DTC Detection Condition | Trouble Area |
| B2343 | The sliding roof drive gear (sliding roof ECU) has not been initialized | Sliding roof drive gear sub-assembly (Sliding roof ECU)
Map light assembly (Sliding roof switch)
Harness or connector
|
WIRING DIAGRAM
INSPECTION PROCEDURE
| 1.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |
Check that the sliding roof drive gear can be initialized ().
- OK:
- Sliding roof drive gear can be initialized.
Check the DTCs ().
Result| Result | Proceed to |
| No DTC is output | A |
| DTC B2343 is output | B |
| | REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) ()
|
|
|
| 3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT) |
Disconnect the R5 drive gear connector.
Disconnect the R7 map light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Condition | Specified Condition |
| R5-10 (UP) - R7-19 (UP) | Always | Below 1 Ω |
| R5-8 (DWN) - R7-18 (DOWN) | Always | Below 1 Ω |
| R5-7 (OPN) - R7-8 (OPN) | Always | Below 1 Ω |
| R5-9 (CLS) - R7-7 (CLS) | Always | Below 1 Ω |
| R7-17 (GND9) - Body ground | Always | Below 1 Ω |
| R5-2 (E) - Body ground | Always | Below 1 Ω |
| R5-10 (UP) or R7-19 (UP) - Body ground | Always | 10 kΩ or higher |
| R5-8 (DWN) or R7-18 (DOWN) - Body ground | Always | 10 kΩ or higher |
| R5-7 (OPN) or R7-8 (OPN) - Body ground | Always | 10 kΩ or higher |
| R5-9 (CLS) or R7-7 (CLS) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| 4.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) |
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Switch Condition | Specified Condition |
| 19 (UP) - 17 (GND9) | UP switch is pressed | Below 1 Ω |
| 19 (UP) - 17 (GND9) | UP switch is not pressed | 10 kΩ or higher |
| 18 (DOWN) - 17 (GND9) | DOWN switch is pressed | Below 1 Ω |
| 18 (DOWN) - 17 (GND9) | DOWN switch is not pressed | 10 kΩ or higher |
| 8 (OPN) - 17 (GND9) | OPEN switch is pressed | Below 1 Ω |
| 8 (OPN) - 17 (GND9) | OPEN switch is not pressed | 10 kΩ or higher |
| 7 (CLS) - 17 (GND9) | CLOSE switch is pressed | Below 1 Ω |
| 7 (CLS) - 17 (GND9) | CLOSE switch is not pressed | 10 kΩ or higher |
| | REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) ()
|
|
|
| OK | |
| |
| REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) ()
|
|
