DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
READ VALUE USING INTELLIGENT TESTER
CHECK DTC OUTPUT
INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH
CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY LH - NO. 2 MAIN BODY ECU AND BODY GROUND)
DTC B225D Tail Gate Panel Half Switch or Courtesy Switch LH
DESCRIPTION
The No. 2 main body ECU receives the half-latch switch, pawl switch and lower tail gate courtesy switch signals from the lower tail gate lock assembly LH and detects the open/closed status of the lower tail gate. DTC B225D is stored when the No. 2 main body ECU receives a half-latch switch, pawl switch or lower tail gate courtesy switch malfunction signal from the lower tail gate lock assembly LH.
| DTC Code | DTC Detection Condition | Trouble Area |
| B225D |
A half-latch switch, pawl switch or lower tail gate courtesy switch malfunction (open or short circuit) signal from the lower tail gate lock LH is received. |
Lower tail gate lock assembly LH
Harness or connector
No. 2 main body ECU
|
WIRING DIAGRAM
INSPECTION PROCEDURE
| 1.READ VALUE USING INTELLIGENT TESTER |
Check the Data List for proper functioning of the half-latch switch, pawl switch and lower tail gate courtesy switch ().
Body No. 4| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Half Latch Switch LH |
Half-latch switch signal / ON or OFF |
ON: Lower tail gate open
OFF: Lower tail gate closed | - |
| Courtesy Switch LH |
Lower tail gate courtesy switch LH signal / ON or OFF |
ON: Lower tail gate open
OFF: Lower tail gate closed | - |
| Luggage Pawl switch |
Pawl switch signal / ON or OFF |
ON: Lower tail gate lock motor operating
OFF: Lower tail gate open or closed | - |
- OK:
- The display is as specified in the normal condition.
Starting with the lower tail gate closed, open and close the lower tail gate 6 times.
Starting with the lower tail gate closed, open and close the lower tail gate 6 times.
Recheck for DTCs ().
- OK:
- DTC B225D is not output.
| | REPLACE NO. 2 MAIN BODY ECU ()
|
|
|
| OK | |
| |
| USE SIMULATION METHOD TO CHECK ()
|
|
| 3.INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH |
Remove the lower tail gate lock assembly LH ().
Inspect the lower tail gate lock assembly LH ().
| | REPLACE LOWER TAIL GATE LOCK ASSEMBLY LH ()
|
|
|
| 4.CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY LH - NO. 2 MAIN BODY ECU AND BODY GROUND) |
Disconnect the h5 lower tail gate lock assembly LH connector.
Disconnect the L50 and L51 No. 2 main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Condition | Specified Condition |
| h5-1 (HAF) - L51-9 (HAF) | Always | Below 1 Ω |
| h5-2 (FUL) - L51-4 (FUL) | Always | Below 1 Ω |
| h5-4 (POL) - L50-15 (POL) | Always | Below 1 Ω |
| h5-3 (E1) - Body ground | Always | Below 1 Ω |
| h5-1 (HAF) - Body ground | Always | 10 kΩ or higher |
| h5-2 (FUL) - Body ground | Always | 10 kΩ or higher |
| h5-4 (POL) - Body ground | Always | 10 kΩ or higher |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK | |
| |
| REPLACE NO. 2 MAIN BODY ECU ()
|
|