Dtc C1792 Height Control Switch Circuit (Test Mode Dtc)
DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
READ VALUE USING INTELLIGENT TESTER (HEIGHT CONTROL SWITCH (UP), HEIGHT CONTROL SWITCH (DOWN))
TEST MODE INSPECTION
INSPECT SUSPENSION CONTROL SWITCH (HEIGHT CONTROL SWITCH)
CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND)
DTC C1792 Height Control Switch Circuit (Test Mode DTC)
DESCRIPTION
This circuit sends a signal to the suspension control ECU in order to adjust the height to the selected height by the height control switch.
| DTC Code | Detection Condition | Trouble Area |
| C1792 | The test mode procedure is performed. | Harness or connector
Suspension control switch (Height control switch)
Suspension control ECU
|
WIRING DIAGRAM
INSPECTION PROCEDURE
Before performing troubleshooting, inspect the connectors of related circuits.
If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed ().
| 1.READ VALUE USING INTELLIGENT TESTER (HEIGHT CONTROL SWITCH (UP), HEIGHT CONTROL SWITCH (DOWN)) |
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and the tester on.
Enter the following menus: Chassis / AHC / Data List.
According to the display on the tester, read the Data List.
AHC| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Height Control Switch(Up) | Height control switch (Up) /
ON or OFF | ON: Up button of the height control switch is pushed.
OFF: Height control switch is not pushed. | - |
| Height Control Switch(Down) | Height control switch (Down) /
ON or OFF | ON: Down button of the height control switch is pushed.
OFF: Height control switch is not pushed. | - |
- OK:
- On the tester screen, item changes between ON and OFF according to switch operation.
Refer to the Test Mode Procedure and perform the signal check. Check that test mode DTC C1792 is cleared ().
Result| Result | Proceed to |
| DTC C1792 is not cleared | A |
| DTC C1792 is cleared | B |
| | USE SIMULATION METHOD TO CHECK ()
|
|
|
| A | |
| |
| REPLACE SUSPENSION CONTROL ECU ()
|
|
| 3.INSPECT SUSPENSION CONTROL SWITCH (HEIGHT CONTROL SWITCH) |
Remove the suspension control switch ().
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Switch Condition | Specified Condition |
| 8 (LO) - 16 (E) | Down button of the height control switch is pushed. | Below 1 Ω |
| Height control switch is not pushed or the up button is pushed. | 10 kΩ or higher |
| 7 (HI) - 16 (E) | Up button of the height control switch is pushed. | Below 1 Ω |
| Height control switch is not pushed or the down button is pushed. | 10 kΩ or higher |
| | REPLACE SUSPENSION CONTROL SWITCH ()
|
|
|
| 4.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND) |
Disconnect the K34 ECU connector.
Disconnect the V4 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
| Tester Connection | Condition | Specified Condition |
| K34-20 (UPSW) - V4-7 (HI) | Always | Below 1 Ω |
| K34-20 (UPSW) - Body ground | Always | 10 kΩ or higher |
| K34-21 (DNSW) - V4-8 (LO) | Always | Below 1 Ω |
| K34-21 (DNSW) - Body ground | Always | 10 kΩ or higher |
| V4-16 (E) - Body ground | Always | Below 1 Ω |
| | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK | |
| |
| REPLACE SUSPENSION CONTROL ECU ()
|
|
