Rear Crankshaft Oil Seal - Removal

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1VD-FTV ENGINE MECHANICAL

REAR CRANKSHAFT OIL SEAL - REMOVAL

1. PRECAUTION
  • NOTICE:
  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work ().
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  • NOTICE:
  • When disconnecting the cable some systems need to be initialized after the cable is reconnected ().
3. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

()


4. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

()


5. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
Rear Crankshaft Oil Seal - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Put matchmarks on the clutch cover and flywheel.

Loosen each set bolt one turn at a time until spring tension is released.

Remove the 8 set bolts, and pull off the clutch cover.

  • NOTICE:
  • Do not drop the clutch disc.
6. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
  • NOTICE:
  • Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.
7. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
Rear Crankshaft Oil Seal - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a wrench, hold the crankshaft.

  • NOTICE:
  • Do not turn the crankshaft counterclockwise.
  • If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt ().
  • Torque:
  • 108 N*m{ 1101 kgf*cm, 80 ft.*lbf}or more
Rear Crankshaft Oil Seal - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 8 bolts.

Rear Crankshaft Oil Seal - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the rear drive plate spacer labeled A, drive plate and ring gear labeled B and rear crankshaft balancer weight labeled C.

8. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
Rear Crankshaft Oil Seal - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a wrench, hold the crankshaft.

  • NOTICE:
  • Do not turn the crankshaft counterclockwise.
  • If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt ().
  • Torque:
  • 108 N*m{ 1101 kgf*cm, 80 ft.*lbf}or more
Rear Crankshaft Oil Seal - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 8 bolts and flywheel.

9. REMOVE REAR CRANKSHAFT OIL SEAL
Rear Crankshaft Oil Seal - Removal. 1VD-FTV ENGINE MECHANICAL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using a knife, cut off the lip of the oil seal.

Text in Illustration
*1Cut Position
*2Oil Seal

Using a screwdriver, pry out the oil seal.

  • NOTICE:
  • Be careful not to damage the crankshaft.
  • HINT:
  • Tape the screwdriver tip before use.