After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work ().

2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH (w/ Viscous Heater)

Fuel Temperature Sensor - Removal. 1VD-FTV FUEL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Remove the 3 bolts and screw.

Loosen the clip and remove the front fender splash shield LH.

3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH (w/ Viscous Heater)

Remove the 3 bolts and 2 screws.

Loosen the clip and remove the front fender splash shield RH.

4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Viscous Heater)

Remove the 10 bolts and No. 1 engine under cover.

5. REMOVE UPPER RADIATOR SUPPORT SEAL (w/ Viscous Heater)

Remove the 7 clips and upper radiator support seal.

6. DRAIN ENGINE COOLANT (w/ Viscous Heater)

CAUTION:

Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:

Collect the coolant in a container and dispose of it according to the regulations in your area.

Loosen the radiator drain cock plug.

Remove the radiator reservoir cap to drain the coolant in the radiator.

Loosen the oil filter bracket drain cock plug to drain the coolant in the engine.

Fuel Temperature Sensor - Removal. 1VD-FTV FUEL. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Tighten the radiator drain cock plug by hand.

Tighten the oil filter bracket drain cock plug.

Torque:
13 N*m{ 133 kgf*cm, 10 ft.*lbf}

7. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)

()

8. REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

Loosen the No. 1 air hose clamp.

Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.

Remove the 3 nuts, bolt and No. 1 cool air inlet.

Remove the gasket from the air tube RH.

9. REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

Loosen the No. 2 air hose clamp.

Remove the 3 nuts, bolt and No. 2 cool air inlet.

Remove the gasket from the air tube LH.

10. DISCONNECT WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

Text in Illustration
*A	w/ Rear Heater
*B	w/o Rear Heater

11. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Loosen the hose clamp.

Disconnect the mass air flow meter connector and using a clip remover, detach the wire harness clamp from the air cleaner cap.

Detach the 4 clamps and remove the air cleaner cap.

12. REMOVE NO. 1 AIR CLEANER HOSE

Loosen the hose clamp and remove the No. 1 air cleaner hose.

13. REMOVE INTAKE AIR CONNECTOR

w/ Viscous Heater:

Disconnect the 2 connectors from the viscous with magnet clutch heater and water temperature sensor.

Text in Illustration
*A	w/ Viscous Heater

w/o Viscous Heater:

Disconnect the connector from the water temperature sensor.

Using a clip remover, detach the 3 wire harness clamps.

Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.

14. REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Remove the 4 bolts and disconnect the 4 water hose ends, and then remove the heater water pipe.

15. REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

Loosen the hose clamp.

Remove the bolt and No. 1 air cleaner pipe.

16. REMOVE FUEL TEMPERATURE SENSOR

NOTICE:

Before replacing the fuel temperature sensor, be sure to clean the surrounding area.

When replacing the fuel temperature sensor, make sure that your hands are clean and do not use gloves, etc.

If the fuel temperature sensor is dropped, replace it with a new one.

Disconnect the fuel temperature sensor connector.

Using SST, remove the fuel temperature sensor.

SST
09817-33190

Remove the O-ring from the fuel temperature sensor.