Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - 1VD-FTV ENGINE CONTROL
DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1))
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1608)
DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT)
DTC P1608 Engine Lack of Power
DESCRIPTION
This DTC is stored if engine output decreases due to a malfunction in the intake or exhaust system, fuel system or cooling system.
Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| - | With the accelerator pedal fully depressed, engine output decreases for approximately 4 to 10 seconds due to a broken component in the intake or exhaust system, fuel system or cooling system or malfunction in one of those systems. (1 trip detection logic) | Intake system clogged EGR valve stuck closed Deterioration of mass air flow meter (foreign matter present on sensor element etc.) Intake system hose disconnected or cracked Turbocharger sub-assembly vane stuck fully open Manifold absolute pressure sensor Manifold absolute pressure sensor out of range Atmospheric pressure sensor (built into ECM) Suction control valve sticking Fuel leak Fuel pressure sensor (common rail assembly (for bank 1)) Engine coolant leak Radiator assembly clogged Engine coolant temperature sensor Engine coolant temperature sensor out of range or stuck Fuel filter element sub-assembly Injector assembly Fan |
INSPECTION PROCEDURE
- HINT:
In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1608 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine lack of power on hesitation.
As the DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.
As the DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.
If any other DTCs are output, perform troubleshooting for those DTCs first.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.
| 1.DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1)) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Record the stored DTC and freeze frame data.
- HINT:
- This freeze frame data shows the actual engine conditions when the lack of power occurred.
| NEXT | |
| 2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1608) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P1608 is output | A |
| P1608 and other DTCs are output | B |
- HINT:
- If any DTCs other than DTC P1608 are output, troubleshoot those DTCs first.
|
| ||||
| A | |
| 3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT) |
Determine the cause of the problem based on the freeze frame data recorded in Procedure 1.
| Judgment of Data List Values | Problem Cause | Trouble Area | Diagnosis Note |
| "MAF Low" in freeze frame data is ON | Intake air volume introduced via the mass air flow meter is insufficient and fuel injection volume remains suppressed | Intake system clogged EGR valve stuck closed Deterioration of mass air flow meter sub-assembly (foreign matter present on sensor element etc.) | EGR fully closed learning Perform the EGR Active Test
|
| Judgment of Data List Values | Problem Cause | Trouble Area | Diagnosis Note |
| "Boost Pressure Low" in freeze frame data is ON | Actual boost pressure is lower than the target boost pressure and fuel injection volume remains suppressed | Intake system hose disconnected or cracked Turbocharger sub-assembly vane stuck fully open Manifold absolute pressure sensor Manifold absolute pressure sensor out of range Atmospheric pressure sensor (built into ECM) Abnormal pressure difference between the atmospheric pressure sensor and manifold absolute pressure sensor EGR valve stuck closed | The possible malfunctioning areas can be narrowed down by checking "MAF/Estimate MAF Ratio" when "Boost Pressure Low" in the freeze frame data is ON
|
| Judgment of Data List Values | Problem Cause | Trouble Area | Diagnosis Note |
| "MAF/Estimate MAF Ratio" in freeze frame data is 1.4 or more | Air that has passed through the mass air flow meter leaks, and the estimated intake air volume becomes less than the actual intake air volume. | Intake air leak due to intake pipe disconnection or cracks between the turbocharger sub-assembly and intercooler assembly or between the intercooler assembly and intake manifold. |
|
| "MAF/Estimate MAF Ratio" in freeze frame data is below 0.6 | Air that has not passed through the mass air flow meter is supplied to the engine, and the actual intake air volume becomes less than the estimated intake air volume. | Air entering due to intake pipe disconnection or cracks between the turbocharger sub-assembly and intercooler assembly or between the intercooler assembly and intake manifold. |
| Judgment of Data List Values | Problem Cause | Trouble Area | Diagnosis Note |
| "Common Rail Pressure Low" in freeze frame data is ON | Common rail pressure remains below the target value. | Suction control valve sticking Fuel leak Fuel filter element sub-assembly clogged Fuel pressure sensor (common rail assembly (for bank 1)) |
|
| Judgment of Data List Values | Problem Cause | Trouble Area | Diagnosis Note |
| "Engine Coolant Temp High" in freeze frame data is ON | Coolant temperature remains high (overheating) and fuel injection volume remains suppressed. | Engine coolant leak Radiator assembly clogged Engine coolant temperature sensor Engine coolant temperature sensor out of range or stuck Fan | Cooling system including radiator assembly |
- HINT:
- Perform the next inspection if there are no problems with the above items.
| NEXT | ||
| ||