Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - AB60F AUTOMATIC TRANSMISSION / TRANSAXLE

DESCRIPTION

MONITOR DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

INSPECT TRANSMISSION CONTROL SWITCH

CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)

CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC CodeDTC Detection ConditionTrouble Area
P0705When one of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
P input signal
N input signal
R input signal
D input signal
(B) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
NSW input signal
R input signal
D input signal
(C) Any of the following signals are ON for 2.0 sec. or more when the shift lever is in S (2 trip detection logic).
NSW input signal
P input signal
N input signal
R input signal
(D) All the signals are OFF simultaneously for the P, R, N and D positions (2 trip detection logic).
Park/neutral position switch
Transmission control switch (Lower shift lever assembly)
Open or short in park/neutral position switch circuit
ECM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.


The park/neutral position switch detects the shift lever position and sends a signal to the ECM.


For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.


The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).


The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.


WIRING DIAGRAM

Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input). AB60F AUTOMATIC TRANSMISSION / TRANSAXLE. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input). AB60F AUTOMATIC TRANSMISSION / TRANSAXLE. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

INSPECTION PROCEDURE

DATA LIST
  • HINT:
  • Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
  • NOTICE:
  • In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

Warm up the engine.

Turn the ignition switch off.

Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON.

Turn the intelligent tester on.

Enter the following menus: Powertrain / ECT / Data List.

According to the display on the tester, read the Data List.

ECT
Tester DisplayMeasurement Item/RangeNormal ConditionDiagnostic Note
Neutral Position SW SignalPNP switch status/
ON or OFF		Shift lever:
In P or N: ON
Not in P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range)PNP switch status/
ON or OFF		Shift lever:
In R: ON
Not in R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range)PNP switch status/
ON or OFF		Shift lever:
In P: ON
Not in P: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range)PNP switch status/
ON or OFF		Shift lever:
In N: ON
Not in N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (D Range)PNP switch status/
ON or OFF		Shift lever:
In D: ON
Not in D: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Sports Shift Up SWSport shift up switch status/
ON or OFF
ON: Shift lever held in "+" (up-shift)
OFF: Shift lever not in "+" (up-shift)
-
Sports Shift Down SWSport shift down switch status/
ON or OFF
ON: Shift lever held in "-" (down-shift)
OFF: Shift lever not in "-" (down-shift)
-
1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input). AB60F AUTOMATIC TRANSMISSION / TRANSAXLE. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the park/neutral position switch connector.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    2 (RB) - 6 (PL)
    4 (B) - 5 (L)
    		Shift lever in PBelow 1 Ω
    2 (RB) - 1 (RL)Shift lever in RBelow 1 Ω
    2 (RB) - 9 (NL)
    4 (B) - 5 (L)
    		Shift lever in NBelow 1 Ω
    2 (RB) - 7 (DL)
    Shift lever in D
    Shift lever in S, "+" or "-"
    		Below 1 Ω
    2 (RB) - 6 (PL)
    4 (B) - 5 (L)
    		Shift lever not in P10 kΩ or higher
    2 (RB) - 1 (RL)Shift lever not in R10 kΩ or higher
    2 (RB) - 9 (NL)
    4 (B) - 5 (L)
    		Shift lever not in N10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever not in D
    Shift lever not in S, "+" or "-"
    		10 kΩ or higher
NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY ()
OK
2.INSPECT TRANSMISSION CONTROL SWITCH
Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input). AB60F AUTOMATIC TRANSMISSION / TRANSAXLE. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the transmission control switch connector.

Measure the resistance according to the value(s) in the table below.

  • Standard Resistance:
  • Tester ConnectionConditionSpecified Condition
    3 (IG) - 7 (S)Shift lever in S, "+" or "-"Below 1 Ω
    3 (IG) - 7 (S)Shift lever not in S, "+" or "-"10 kΩ or higher
NG
REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY) ()
OK
3.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input). AB60F AUTOMATIC TRANSMISSION / TRANSAXLE. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the park/neutral position switch connector.

Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionSwitch ConditionSpecified Condition
    C24-2 (RB) - Body groundIgnition switch ON11 to 14 V
    C24-2 (RB) - Body groundIgnition switch offBelow 1 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BK/UK LP FUSE)
OK
4.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input). AB60F AUTOMATIC TRANSMISSION / TRANSAXLE. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the transmission control switch connector.

Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • Tester ConnectionSwitch ConditionSpecified Condition
    E52-3 (IG) - Body groundIgnition switch ON11 to 14 V
    E52-3 (IG) - Body groundIgnition switch offBelow 1 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - LH-IG FUSE)
OK
5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input). AB60F AUTOMATIC TRANSMISSION / TRANSAXLE. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the ECM connector.

Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • for LHD
    Tester ConnectionConditionSpecified Condition
    C45-31 (P) - Body ground
    A38-43 (NSW) - Body ground
    Ignition switch ON
    Shift lever in P
    		11 to 14 V
    C45-30 (R) - Body ground
    Ignition switch ON
    Shift lever in R
    		11 to 14 V*
    C45-29 (N) - Body ground
    A38-43 (NSW) - Body ground
    Ignition switch ON
    Shift lever in N
    		11 to 14 V
    C45-28 (D) - Body ground
    Ignition switch ON
    Shift lever in D
    		11 to 14 V
    C45-31 (P) - Body ground
    A38-43 (NSW) - Body ground
    Ignition switch ON
    Shift lever not in P
    		Below 1 V
    C45-30 (R) - Body ground
    Ignition switch ON
    Shift lever not in R
    		Below 1 V
    C45-29 (N) - Body ground
    A38-43 (NSW) - Body ground
    Ignition switch ON
    Shift lever not in N
    		Below 1 V
    C45-28 (D) - Body ground
    Ignition switch ON
    Shift lever not in D
    		Below 1 V
  • for RHD
    Tester ConnectionConditionSpecified Condition
    C46-31 (P) - Body ground
    A52-43 (NSW) - Body ground
    Ignition switch ON
    Shift lever in P
    		11 to 14 V
    C46-30 (R) - Body ground
    Ignition switch ON
    Shift lever in R
    		11 to 14 V*
    C46-29 (N) - Body ground
    A52-43 (NSW) - Body ground
    Ignition switch ON
    Shift lever in N
    		11 to 14 V
    C46-28 (D) - Body ground
    Ignition switch ON
    Shift lever in D
    		11 to 14 V
    C46-31 (P) - Body ground
    A52-43 (NSW) - Body ground
    Ignition switch ON
    Shift lever not in P
    		Below 1 V
    C46-30 (R) - Body ground
    Ignition switch ON
    Shift lever not in R
    		Below 1 V
    C46-29 (N) - Body ground
    A52-43 (NSW) - Body ground
    Ignition switch ON
    Shift lever not in N
    		Below 1 V
    C46-28 (D) - Body ground
    Ignition switch ON
    Shift lever not in D
    		Below 1 V
  • HINT:
  • *: The voltage will drop slightly due to the turning on of the back up light.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
Dtc P0705 Transmission Range Sensor Circuit Malfunction (Prndl Input). AB60F AUTOMATIC TRANSMISSION / TRANSAXLE. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Disconnect the ECM connector.

Turn the ignition switch to ON.

Measure the voltage according to the value(s) in the table below.

  • Standard Voltage:
  • for LHD
    Tester ConnectionConditionSpecified Condition
    A38-25 (S) - Body groundShift lever in S, "+" or "-"11 to 14 V
    A38-25 (S) - Body groundShift lever not in S, "+" or "-"Below 1 V
  • for RHD
    Tester ConnectionConditionSpecified Condition
    A52-25 (S) - Body groundShift lever in S, "+" or "-"11 to 14 V
    A52-25 (S) - Body groundShift lever not in S, "+" or "-"Below 1 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE ECM ()
AB60F AUTOMATIC TRANSMISSION / TRANSAXLE
Land Cruiser URJ200 URJ202 GRJ200 VDJ200
AUTOMATIC TRANSMISSION SYSTEM for 1VD-FTV