Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - CLUTCH
CLUTCH PEDAL (for LHD) - REMOVAL
| 1. DRAIN CLUTCH FLUID |
| 2. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION |
Put protective tape around the No. 2 instrument panel finish panel cushion.
| *1 | Protective Tape |
Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.
| 3. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH |
Remove the clip and screw.
Detach the 8 claws.
Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.
| 4. REMOVE INSTRUMENT SIDE PANEL LH |
Place protective tape as shown in the illustration.
| *1 | Protective Tape |
Using a moulding remover, detach the 6 claws and remove the instrument side panel.
| 5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Place protective tape as shown in the illustration.
| *1 | Protective Tape |
Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.
| 6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Place protective tape as shown in the illustration.
Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.
| *A | w/ Entry and Start System | *B | w/o Entry and Start System |
| *1 | Protective Tape | - | - |
| 7. REMOVE FRONT DOOR SCUFF PLATE LH |
Detach the 7 claws and 4 clips, and remove the scuff plate.
| 8. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover) |
Remove the 2 screws.
Detach the 3 claws.
Disconnect the connectors and remove the No. 1 instrument panel under cover.
| 9. REMOVE COWL SIDE TRIM BOARD LH |
Remove the cap nut.
Detach the 2 clips and remove the cowl side trim board.
| 10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Using a screwdriver, detach the 2 claws and open the hole cover.
- HINT:
- Tape the screwdriver tip before use.
| *1 | Protective Tape |
w/ Driver Side Knee Airbag:
Remove the 2 bolts.
Detach the 16 claws.
w/o Driver Side Knee Airbag:
Remove the 2 bolts.
Detach the 9 claws.
for Automatic Air Conditioning System:
Detach the 2 claws and remove the room temperature sensor.
Detach the 2 claws and disconnect the 2 control cables.
Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.
| 11. REMOVE NO. 1 SWITCH HOLE BASE |
Detach the 4 claws.
Disconnect the connectors and remove the No. 1 switch hole cover.
| 12. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
Remove the 5 bolts and driver side knee airbag.
Disconnect the connector.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
| 13. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
Detach the 2 claws and disconnect the DLC3.
Remove the 5 bolts and lower instrument panel.
| 14. REMOVE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |
Remove the 3 bolts.
Disconnect the 9 ECU connectors and remove the ECU.
| 15. DISCONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE AND CLUTCH RESERVOIR TUBE |
Using a union nut wrench, disconnect the flexible hose tube.
- HINT:
- Use a container to catch the fluid.
Disconnect the clutch reservoir tube.
| 16. REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY WITH CLUTCH MASTER CYLINDER |
Disconnect the clutch start switch connector.
w/ Cruise Control System:
Disconnect the clutch switch connector.
Remove the 2 nuts, bolt and clutch pedal support with clutch master cylinder.
| 17. REMOVE TURNOVER SPRING |
Move the pedal to the full stroke position.
Remove the turnover spring.
| 18. REMOVE CLUTCH PEDAL SPRING |
Remove the 2 E-rings and the spring with spacer.
Remove the spacer from the spring.
| 19. REMOVE CLUTCH PEDAL SUB-ASSEMBLY |
Remove the clip, wave washer and clevis pin.
Remove the nut, washer and bolt.
Remove the clutch pedal from the clutch pedal support.
| 20. REMOVE CLUTCH PEDAL PAD |
Remove the clutch pedal pad from the clutch pedal.
| 21. REMOVE CLUTCH PEDAL SHAFT COLLAR |
Remove the clutch pedal shaft collar from the clutch pedal.
| 22. REMOVE CLUTCH PEDAL BUSH |
Remove the 2 bushes from the clutch pedal.
| 23. REMOVE NO. 2 CLUTCH PEDAL CUSHION |
Remove the 2 clutch pedal cushions from the clutch pedal.
| 24. REMOVE CLUTCH PEDAL TURNOVER BUSH |
Remove the clutch pedal turnover bush from the clutch pedal.
| 25. REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH |
Remove the push rod clevis bush from the clutch pedal.
| 26. REMOVE CLUTCH PEDAL SPRING HOLDER |
Remove the clutch pedal spring holder from the clutch pedal support.