Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - JF2A TRANSFER / 4WD / AWD
4WD CONTROL ECU - INSTALLATION
| 1. INSTALL FOUR WHEEL DRIVE CONTROL ECU |
Install the ECU with the bolt.
- Torque:
- 13 N*m{ 127 kgf*cm, 9 ft.*lbf}
Connect the 2 ECU connectors.
| 2. INSTALL STEERING CONTROL ECU (for RHD) |
Install the steering control ECU to the junction block with the 2 bolts.
- Torque:
- for bolt A:
- 5.5 N*m{ 56 kgf*cm, 49 in.*lbf}
- for bolt B:
- 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}
| 3. INSTALL STEERING CONTROL WITH JUNCTION BLOCK (for RHD) |
Front side: Connect the 3 connectors.
Rear side:
Install the steering control ECU with junction block with the bolt and 2 nuts.
- Torque:
- 8.0 N*m{ 82 kgf*cm, 71 in.*lbf}
Connect the 2 connectors.
| 4. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for LHD) |
Connect the connector.
Attach the 3 claws to install the lower No. 2 instrument panel finish panel.
Install the 4 bolts.
| 5. INSTALL INSTRUMENT PANEL BOX DOOR KNOB (for LHD) |
Attach the 2 claws to install the instrument panel box door knob.
| 6. INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD) |
Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.
| 7. INSTALL COWL SIDE TRIM BOARD RH |
Attach the 2 clips to install the cowl side trim board.
Install the cap nut.
| 8. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (for RHD) |
Connect the connector.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Install the driver side knee airbag with the 5 bolts.
- Torque:
- 10 N*m{ 102 kgf*cm, 7 ft.*lbf}
| 9. INSTALL NO. 1 SWITCH HOLE BASE (for RHD) |
Connect the connectors.
Attach the 4 claws to install the No. 1 switch hole base.
| 10. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for RHD) |
Connect the connectors.
for Automatic Air Conditioning System:
Attach the 2 claws to install the room temperature sensor.
Attach the 2 claws to connect the 2 control cables.
w/ Driver Side Knee Airbag:
Attach the 16 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.
w/o Driver Side Knee Airbag:
Attach the 9 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.
Attach the 2 claws to close the hole cover.
| 11. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD) |
w/ Floor Under Cover: ()
| 12. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD) |
Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.
| *A | w/ Entry and Start System | *B | w/o Entry and Start System |
| 13. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD) |
Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.
| 14. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (for LHD) |
Connect the connector.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Attach the 4 claws to install the front passenger side knee airbag.
Install the 4 bolts.
- Torque:
- 10 N*m{ 102 kgf*cm, 7 ft.*lbf}
| 15. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD) |
w/ Floor Under Cover: ()
| 16. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH |
Attach the 7 claws to install the lower instrument panel pad sub-assembly.
Install the clip and screw.
| 17. INSTALL NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION |
Attach the 7 claws to install the No. 1 instrument panel finish panel cushion.
| 18. INSTALL FRONT DOOR SCUFF PLATE RH |
- HINT:
- Use the same procedures described for the LH side.
| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected ().
| 20. CHECK SRS WARNING LIGHT |
()