Vehicle Stability Control System - Dtc Check / Clear

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS


VEHICLE STABILITY CONTROL SYSTEM - DTC CHECK / CLEAR

DTC CHECK/CLEAR (When Using GTS)

Check for DTCs.

Turn the ignition switch off.

Connect the GTS to the DLC3.

Turn the ignition switch to ON.

Turn the GTS on.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Read the DTCs by following the prompts on the GTS screen.

Clear the DTCs.

Turn the ignition switch off.

Connect the GTS to the DLC3.

Turn the ignition switch to ON.

Turn the GTS on.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Operate the GTS to clear the codes.

  • HINT:
  • Refer to the GTS operator's manual for further details.
DTC CHECK/CLEAR (When Using SST Check Wire)

Check for DTCs.

Vehicle Stability Control System - Dtc Check / Clear. BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

  • SST
  • 09843-18040
Text in Illustration
*aFront view of DLC3

Turn the ignition switch to ON.

Read the DTCs output from the ABS warning light and slip indicator light in the combination meter.

  • HINT:
When the system is normal, the ABS warning light and slip indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
When only 1 DTC is stored, the light outputs the same code after an interval of 4 seconds. Example: When DTC 21 is stored, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.
When 2 or more DTCs are stored, the light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.
If no code is output, inspect the TC and CG terminal circuit and the ABS warning light and slip indicator light circuits.
Trouble AreaSee Procedure
TC and CG terminal circuit
ABS warning light circuit (Remains on)
ABS warning light circuit (Does not come on)
Slip indicator light circuit (Remains on)
Slip indicator light circuit (Does not come on)

The codes are explained in the code table.

ABS DTC
ABS Warning Light DisplayGTS Display
11C146E
12C146F
21C1468
22C1469
23C146A
24C146B
25C1225
26C1226
27C1227
28C1228
31C1401
C1405
C1409
32C1402
C1406
C1410
33C1403
C1407
C1411
34C1404
C1408
C1412
35C1413
36C1414
37C1337
38C1415
39C1416
41C1241
C1417
42C1242
43C1243
44C1419
C1420
C1442
45C1245
46C1421
C1422
C1423
C1424
C1455
C1456
C1457
C1458
49C1425
51C1251
52C1252
53C1253
54C1254
56C1256
C1452
57C1257
58C1453
C1454
68C1268
94U0073
95U0124
97C1381
98C1336
A1*U0114
*: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.
VSC DTC
Slip Indicator Light DisplayGTS Display
13C120A
31C1432
C1433
C1434
32C1232
34C1435
C1436
C1443
36C1210
39C1336
43*-
47C1340
51C1201
53C1203
62U0123
63U0126
64C1380
65C1437
U0100
66C1290
C1439
C1445
68U0130
98C1440
*: This DTC is output when the VSC system detects a malfunction in the ABS.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.


If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.

Clear the DTCs.

Vehicle Stability Control System - Dtc Check / Clear. BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

  • SST
  • 09843-18040
Text in Illustration
*aFront view of DLC3

Turn the ignition switch to ON.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

Check that the ABS warning light and slip indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

Remove SST from the terminals of the DLC3.

END OF DTC CHECK/CLEAR

Turn the ignition switch to ON.

Check that the ABS warning light and slip indicator light go off within approximately 3 seconds.