Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - AUDIO / VIDEO

CHECK HARD DISK DRIVE

CHECK PANEL & STEERING SWITCH

CHECK TOUCH SWITCH

CHECK MIC & VOICE RECOGNITION

CHECK COLOR BAR

CHECK GPS & VEHICLE SENSORS

CHECK VEHICLE SIGNAL

CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING

CHECK DAB RECEPTION (w/ DAB Function)

CHECK UNIT VERSION INFORMATION

CHECK SOFTWARE ERROR HISTORY

CHECK OPTICAL DISC ERROR HISTORY

AUDIO AND VISUAL SYSTEM (w/ Navigation System) - OPERATION CHECK

CHECK HARD DISK DRIVE

HINT:

Check the hard disk drive (HDD) built into the multi-media module receiver assembly.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Audio And Visual System (W/ Navigation System) - Operation Check. AUDIO / VIDEO. Land Cruiser URJ200 URJ202 GRJ200 VDJ200

Select "Failure Diagnosis" from the "Service Menu" screen.

Select "HDD Check" from the "Failure Diagnosis" screen.

HDD Check

Select "HDD Check" to start the HDD check.

Check that the result is displayed when the HDD check is completed.

Screen Description
Display (Result)	Description
Checking	Check is in progress
OK	Hard disk drive is normal
NG	Hard disk drive is malfunctioning

Text in Illustration
*a	Result

HINT:

After selecting "HDD Check", it may take a while until the result is displayed.

If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the HDD may not operate normally, and "NG" may be shown on the display. Make sure to perform the inspection with the cabin at an appropriate temperature.

If "NG" is displayed even when the cabin temperature is appropriate, replace the HDD with a new one.

CHECK PANEL & STEERING SWITCH

HINT:

The multi-media module receiver assembly panel switches and steering switches are checked in the following procedure.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Function Check/Setting" from the "Service Menu" screen.

Select "Panel&Steering Switch" from the "Function Check/Setting I" screen.

Panel & Steering Switch Check Mode

Operate each switch and check that the switch conditions are correctly displayed.

Screen Description
Display	Content
*a: Switch condition	"Pushed" is displayed when any switch is pushed
*b: Number of switches pushed	Number of switches pushed at once is displayed If more than 3 switches are pushed at once, "More than 3" is displayed
*c: Rotary switch direction	Direction of rotary switch is displayed

NOTICE:

When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

CHECK TOUCH SWITCH

HINT:

The touch switches on the screen are checked in the following procedure.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Function Check/Setting" from the "Service Menu" screen.

Select "Touch Switch" from the "Function Check/Setting I" screen.

Touch Switch Check

Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:

A "+" mark is displayed where the display is touched.

The "+" mark remains on the display even after the finger is removed.

CHECK MIC & VOICE RECOGNITION

HINT:

The microphone and microphone input level are checked in the following procedure.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Function Check/Setting" from the "Service Menu" screen.

Select "Mic&Voice Recognition" from the "Function Check/Setting I" screen.

Microphone & Voice Recognition Check

Screen Description
Display	Content
*a: Microphone input level meter	Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
*b: Recording switch	Starts recording.
*c: Stop switch	Stops recording and playing.
*d: Play switch	Plays the recorded voice.
*e: Recording indicator	Comes on while recording.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.

Push the recording switch and perform voice recording.

HINT:

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

While recording or playing, the switches other than the stop switch cannot be pushed.

When no recording is present, the play switch cannot be pushed.

Recording will stop after 5 seconds or when the stop switch is pushed.

Check that the recording indicator remains on while recording and that the recording can be played normally.

CHECK COLOR BAR

HINT:

The display color on the screen is checked in the following procedure.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Function Check/Setting" from the "Service Menu" screen.

Select "Color Bar" from the "Function Check/Setting I" screen.

Color Bar Check Mode

Select a color bar from the "Color Bar Check Mode" screen.

Check the display color.

HINT:

The entire screen turns to the color or stripe selected.

Touching the display will return to the "Color Bar Check Mode" screen.

CHECK GPS & VEHICLE SENSORS

HINT:

GPS information, vehicle signals and sensor signals are checked in the following procedure.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Function Check/Setting" from the "Service Menu" screen.

Select "GPS&Vehicle Sensors" from the "Function Check/Setting I" screen.

Select "Sensors Check" from the "GPS Information" screen.

Vehicle Sensors

Screen Description
Display	Content
*a: Vehicle signal	Vehicle speed signal condition is displayed.
*b: Sensor signal	Gyro sensor output condition is displayed.

HINT:

This screen is updated once per second.

Check all the signals and sensors when vehicle signal information is displayed.

CHECK VEHICLE SIGNAL

HINT:

Vehicle signals received by the multi-media module receiver assembly are checked in the following procedure.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Function Check/Setting" from the "Service Menu" screen.

Select "Vehicle Signal" from the "Function Check/Setting I" screen.

Vehicle Signal Check Mode

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

Screen Description
Display	Content
Battery	Battery voltage is displayed.
IG	Engine switch ON/OFF state is displayed.
PKB	Parking brake ON/OFF state is displayed.
REV	Reverse signal ON/OFF state is displayed.
SPEED	Vehicle speed is displayed in km/h.
TAIL	Tail signal (Light control switch) ON/OFF state is displayed.
ADIM/TCAN	Brightness state DIM (with) / BRIGHT (without) is displayed.

HINT:

Only items sending vehicle signals will be displayed.

This screen displays vehicle signals input to the multi-media module receiver assembly.

This screen is updated once per second when vehicle input signals change.

CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING

HINT:

The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Function Check/Setting" from the "Service Menu" screen.

Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)

Screen Description
Display	Content
*a: Receive voice level adjustment	Setting for the voice level received from "Bluetooth" compatible phones.
*b: Send voice level adjustment	Setting for the voice level sent from "Bluetooth" compatible phones.

NOTICE:

Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.

If the voice level is low, press the up button, and if the voice level is loud, press the down button.

HINT:

Settings will be applied when the up or down button is selected.

The received voice level adjustment ranges from -5 to +1.

The sent voice level adjustment ranges from -5 to +4.

The initial level is "0".

Hands-Free Voice Quality Setting (Voice Quality Type adjustment)

Screen Description
*a	Numeric keypad
*b	Setting button
*c	Reset button

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Settings
Parameter	Target Phenomenon	Voice Quality Type	Positive Effect of Changing Voice Quality	Negative Effect of Changing Voice Quality
A (Noise)	The change in background noise the other party hears becomes unpleasant.	1000	The change in background noise the other party hears is reduced.	Background noise when not talking becomes large.
B (Noise)	The volume of the noise the other party hears temporarily becomes large.	2000	The temporary noise is reduced.	The volume of voice may drop temporarily.
C (Echo)	The other party hears weak echoes.	0100	The amount of echo is reduced (low level).	Sound quality of the other party deteriorates (low level).
D (Echo)	The other party hears strong echoes.	0200	The amount of echo is reduced (high level).	Sound quality of the other party deteriorates (high level).
E (Quality)	The other party hears harsh noises.	0010	Sound the other party hears becomes soft.	Sound the other party hears becomes muffled.
F (Quality)	You hear harsh noises.	0020	Sound you hear becomes soft.	Sound you hear becomes muffled.

Settings (When multiple phenomenon occurred)
Parameter	Target Phenomenon	Voice Quality Type	Positive Effect of Changing Voice Quality	Negative Effect of Changing Voice Quality
A+C	The change in background noise the other party hears becomes unpleasant and the other party hears weak echoes.	1100	The change in background noise the other party hears is reduced. The amount of echo is reduced (low level).	Background noise when not talking becomes large. Sound quality of the other party deteriorates (low level).
A+D	The change in background noise the other party hears becomes unpleasant and the other party hears strong echoes.	1200	The change in background noise the other party hears is reduced. The amount of echo is reduced (high level).	Background noise when not talking becomes large. Sound quality of the other party deteriorates (high level).
B+C	The volume of the noise the other party hears temporarily becomes large and the other party hears weak echoes.	2100	The temporary noise is reduced. The amount of echo is reduced (low level).	The volume of voice may drop temporarily. Sound quality of the other party deteriorates (low level).
B+D	The volume of the noise the other party hears temporarily becomes large and the other party hears strong echoes.	2200	The temporary noise is reduced. The amount of echo is reduced (high level).	The volume of voice may drop temporarily. Sound quality of the other party deteriorates (high level).
C+E	The other party hears weak echoes and harsh noises.	0110	The amount of echo is reduced (low level). Sound the other party hears becomes soft.	Sound quality of the other party deteriorates (low level). Sound the other party hears becomes muffled.
C+F	The other party hears weak echoes and you hear harsh noises.	0120	The amount of echo is reduced (low level). Sound you hear becomes soft.	Sound quality of the other party deteriorates (low level). Sound you hear becomes muffled.

HINT:

The default value is "0000".

Settings will be applied when the setting button is selected.

If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.

CHECK DAB RECEPTION (w/ DAB Function)

HINT:

The reception condition of DAB (Digital Audio Broadcast) can be checked.

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Function Check/Setting" from the "Service Menu" screen.

Select "Next Page" from the "Function Check/Setting I" screen.

Select "DAB Reception Check" from the "Function Check/Setting II" screen.

*a: Channel Change Switch Description
Display	Content
Up or down button	Enables the channel to be changed to the one to be checked.

*b: Check Switch Description
Display	Condition	Content
Check	Before/after check	Starts checking
STOP	During check	Stops checking

*c: Antenna Connection Check Result Description
Display	Content
OK	Connected properly
NG	Not connected properly
-	Not equipped with DAB antenna.

*d: DAB Tuner Reception Level Check Result Description
Display	Content
Black	Good reception
Red	Poor reception
-	Not equipped with DAB antenna.

Select the "Check" button to start the DAB reception check.

Check that the result is displayed when the DAB reception check is performed.

CHECK UNIT VERSION INFORMATION

HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode ().

Select "Service Information" from the "Service Menu" screen.

Select "Version Information" from the "Service Information" screen.

Press the "Push" switch.

Unit Version Information

Screen Description
Display	Content
*a: Device name	Target device
*b: Manufacturer name	Manufacturer of the ECU (target device)
*c: Component name	Component name of the ECU (target device)
*d: Version	Version of the ECU (target device)

HINT:

Depending on the manufacturer, some component names and versions will be displayed differently.

CHECK SOFTWARE ERROR HISTORY

HINT:

This function is used to check the cause when the multi-media module receiver assembly screen is blacked out.

Check software error history.

Connect the intelligent tester to the DLC3.

Turn the engine switch on (IG).

Turn the intelligent tester on.

Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

When an item is stored for Software Error History, record it before repairing the multi-media module receiver assembly.

Software Error History Screen Description
Error Description	Trigger	Detail
Software Reset	Navi Microcomputer	Hexadecimal Number
	Audio Microcomputer
	CAN Microcomputer
No Video Signal	Front Monitor
No Video Signal	Rear Monitor
MOST Cold Restart	Always

HINT:

Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

If an error that is unsupported by the intelligent tester occurs, a "-" is displayed for the display items.

Clear software error history.

When DTCs are cleared using any of the following operations, Software Error History will be cleared as well ().

Cleared using the intelligent tester.

Cleared using the system check mode screen.

Cleared using the unit check mode screen.

CHECK OPTICAL DISC ERROR HISTORY

HINT:

This function is used to check the cause when an optical disc error occurs.

Check optical disc error history.

Connect the intelligent tester to the DLC3.

Turn the engine switch on (IG).

Turn the intelligent tester on.

Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

Optical Disc Error History Screen Description
Display	Content
Error Type	Displays the type of error.
Device	Displays the malfunctioning device.
Date	Displays the date and time that the malfunction occurred.

"Error Type" Screen Description
Error Type	Detection Condition	Action
Read Error	When a disc read error occurs.	Proceed to next suspected area shown in Problem Symptoms Table ()
Disc damaged/up side down/dirty	When it is determined that any of the following is the cause of the disc read error: The disc cannot be read. The disc cannot be read because of dirt or scratches. The disc cannot be read because it is inserted up side down.
Cannot determine disc type	An unsuitable disc is inserted.
DPS error	When an error occurs while decoding MP3/WMA files.
Some files are corrupt	When MP3/WMA files cannot be played back because they are unsupported. Even though the file extensions are MP3 or WMA, files cannot be played back because the header information cannot be read.
Some files cannot be found	When a disc without music data is played back. When there are no playable MP3/WMA files.
Copy protection violation	When a file with copyright protection that cannot be played back is played back.

"Device" Screen Description
Device	Component
DVD-P	Multi-media module receiver assembly
CD-P	Not available
R-Seat DVD-P	Not available

HINT:

Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

If an error that is unsupported by the intelligent tester occurs, a "-" or blank is displayed for the display items.

Clear optical disc error history.

When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well ().

Cleared using the intelligent tester.

Cleared using the system check mode screen.

Cleared using the unit check mode screen.

Audio And Visual System (W/ Navigation System) - Operation Check

Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - AUDIO / VIDEO

AUDIO AND VISUAL SYSTEM (w/ Navigation System) - OPERATION CHECK