Масляный Радиатор Двигателя Установка. Corolla Auris

Check and clean the oil cooler installation surface.

Apply engine oil to the O-ring of the oil cooler.

With the antirotation bracket of the oil cooler being in contact with the oil pan side, temporarily install the oil cooler with the nut.

Using SST, tighten the nut to the specified torque.

SST

09229-55010

Момент затяжки:

66 Н*м{673 кгс*см, 49 фунт-сила-футов}

Connect the oil cooler hose to the oil cooler.

Check and clean the oil filter installation surface.

Apply clean engine oil to the gasket of a new oil filter.

Lightly screw the oil filter into place, then tighten it until the gasket comes into contact with the seat.

Using SST, tighten the oil filter.
Depending on the work space available, choose from the following:

SST

09228-07501

1. If enough space is available, use a torque wrench to tighten the oil filter.
   

   Момент затяжки:

   18 Н*м{180 кгс*см, 13 фунт-сила-футов}

2. If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or use a common wrench.
   

Close the service cover.

Fill with fresh engine oil.

Engine oil:

Oil Grade	Oil Viscosity (SAE)
ACEA B1 API CF-4 or CF (you may also use API CE or CD.)	5W-30 10W-30 15W-40 20W-50

Capacity:

Item	Fill amount
Drain and refill with oil filter change	4.3 liters (4.5 US qts, 3.8 lmp. qts)
Drain and refill without oil filter change	3.8 liters (4.0 US qts, 3.3 lmp. qts)
Dry fill	4.8 liters (5.1 US qts, 4.2 lmp. qts)

Tighten the radiator drain cock plug.

Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.

Standard capacity:

Item	Specified Condition
without Power heater	5.4 liters (5.7 US qts, 4.8 lmp. qts)
with Power heater	5.8 liters (6.1 US qts, 5.1 lmp. qts)

УКАЗАНИЕ:

1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
   
2. Contact your TOYOTA dealer for further details.
   

ПРИМЕЧАНИЕ:

Never use water as a substitute for engine coolant.

Remove the radiator cap and air-bleeding valve and add coolant to line B of the reservoir tank.

Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.

Install the cap and valve, and warm up the engine sufficiently.

Bleed air from the cooling system.

ПРИМЕЧАНИЕ:

1. Before starting the engine, turn the A/C switch OFF.
   
2. Adjust the air conditioner set temperature to MAX (HOT).
   
3. Adjust the air conditioner set blower to Lo.
   

1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.
   

   УКАЗАНИЕ:

   The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

   ПРЕДОСТЕРЕЖЕНИЕ:

   When squeezing the radiator hose:

   1. Wear protective gloves.
      
   2. Be careful as the radiator hoses are hot.
      
   3. Keep your hands away from the radiator fan.
      

2. After the engine has warmed up, run the engine using the following cycle for at least 7 minutes: at 3000 rpm for 5 seconds, at idle speed for 45 seconds. (Repeat this cycle at least 8 times.)
   

3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.
   

   ПРЕДОСТЕРЕЖЕНИЕ:

   When squeezing the radiator hose:

   1. Wear protective gloves.
      
   2. Be careful as the radiator hoses are hot.
      
   3. Keep your hands away from the radiator fan.
      

After the engine has cooled down, check that the coolant level is between FULL and LOW.
If the coolant level is low, add coolant to the reservoir tank F line.

Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

Pump it to 108 kPa (1.1 kgf/cm², 15.6 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.